How To Listen To The Fm Radio; Setup And Special Configurations - Midland BTX2 PRO Guide D'utilisation

3. Now press firmly (3 sec) the "Volume +" or "Volume -" button, the Blue and Red
lights will flash.
4. Enable the Bluetooth device search feature on your GPS
5. After some seconds, "Midland BTX2 PRO" will be displayed on your GPS.
6. Follow the pairing procedure of your GPS. If a pin code is requested you must enter
"0000" (four times zero).
When successfully paired, the Blue light of the unit will be on for one second and then
the unit will exit the setup mode and switch to the working mode (the Blue light will
start flashing). You can now use your Midland BTX2 PRO and the GPS street voice
announcement are always in background. If you pair the GPS to the Volume + button
(because for example the "Volume –" button was already used), you lose the possibility
to pair the phone to the Midland BTX2 PRO unit. You can overcome this limit by pai-
ring the phone directly to the GPS and then the GPS to the Midland BTX2 PRO unit.
All the phone features are therefore managed by the GPS itself.
Pairing to a PMR446 radio with integrated or external Bluetooth
The PMR446 Radio can be paired to the "Volume +" or "Volume -" button. If paired
on "Volume -" and the "Background" feature is activated, the PMR446 radio is always
in the background even when you talk on the intercom.
Pairing procedure
› Turn off the unit
› Press and hold down the "Middle" button about 7 sec., until the Red light is on per-
manently.
› Now press firmly (3 sec) the "Vol +" or "Vol -" button, the Blue and Red light will
flash.
› Follow now the pairing procedure explained on the manual of the transceiver itself.
C-Radio FM mode
Mode Forward button
FM Radio Short press: seek station up
Long press: Scan recorded
12

How to listen to the FM Radio

The FM Radio receiver is integrated inside the unit. You just need to switch to the "FM
Radio" mode in order to use it. Long press the middle button until you hear "FM radio"
from the voice announcement. Now all the three main buttons are dedicated to the
FM Radio (See Table C).
Press short the Forward or the Backward button to seek the FM Radio station.
When you press long the Forward or the Backward button, you can scan up or down
the 6 recorded stations. A voice announcement will tell you the number of which me-
mory you are entering. To save the station you are listening to, press the Forward and
Backward buttons together for 3 sec. You will hear a beep tone for confirmation.
The station is saved over the last recorded station used.
Thanks to the RDS system, the FM Radio will choose the strongest signal available for
the radio station you like to listen. The RDS system is OFF by default, if needed you
can toggle on/off the RDS pressing together the "Volume +" and "Volume –" buttons
for 3 sec when the radio is on. A voice announcement will tell you the RDS status.
How to Disable/Enable the FM Radio
By default the FM radio is on.
Disabling:
› Enter the "Setup" mode: turn off the unit and hold down the "Middle" button about
7 sec., until the Red light is on permanently.
› Press "Middle" and "Volume+" buttons together for 3 seconds. The blue LED will
flash three times.
› Double click on the "Middle" button to exit the "Setup" mode and use the Midland
BTX2 PRO
Middle button Rear button
Short press: On/off Short press: seek station up
Long press: Change mode Long press: Scan recorded
www.midlandeurope.com
Enabling:
› Follow the same procedure up described; now the blue LED will flash once.
To exit the "Setup" mode, double click the "Middle" button.
FM Radio with intercom
When you are in "FM Radio" mode is not possible to manually open the intercom, you
can only open it using VOX feature (just talk) to the unit paired on the "Middle" button.
To manually activate the intercom you must switch to "Intercom" mode.

Setup and special configurations

Resetting all paired devices
Sometimes you may find it necessary to delete all the pairing references stored in the
Midland BTX2 PRO unit (reset operation).
To perform this operation you must first enter the setup mode:
› Turn off the unit
› Press and hold down the "Middle" button 7 sec., until the Red light is on perma-
nently.
› Then simultaneously press and hold down the "Volume +" and "Volume –" buttons
for 3 seconds. The Blue Light will be lit on for 1 sec and than back to steady RED.
› Double click on the "Middle" button to exit the "Setup" mode.
This procedure deletes all the paired Bluetooth devices stored in the memory and it is
therefore possible to start a new "clean" pairing session.
Back to factory setting
Sometimes you may find it necessary to go back to the factory setting, to reset all the
changes/setup already made and have a "clean" unit.
To perform this operation you must first enter the setup mode:
› Turn off the unit
› Press and hold down the "Middle" button about 7 sec., until the Red light is on per-
manently.
› Then simultaneously press and hold down all the three buttons "Forward"-"Midd-
le"-"Backward" for 3 seconds. The Blue Light will be lit on for 1 sec and than back
to steady RED.
› Double click on the "Middle" button to exit the "Setup" mode and use the Midland
BTX2 PRO
www.midlandeurope.com
Adjusting/ Disabling the VOX feature (Intercom and telephone)
The Intercom feature can be enabled both manually and vocally (VOX). The VOX acti-
vation is influenced by the helmet type, the background noise and therefore by the
speed.
For optimum results, it is possible to choose one of the following four microphone
sensitivity levels: high, medium, low and very low. The default setting of Midland BTX2
PRO is "High". It is also possible to disable the VOX feature in order to activate the
Intercom and phone call answering features in manual mode only.
Adjusting the sensitivity of the (VOX)
To perform this operation you must first enter the setup mode:
1. Turn off the unit
2. Press and hold down the "Middle" button about 7 sec., until the Red light is on per-
manently.
3. Your Midland BTX2 PRO is now in "Set up mode".
4. Press the "Backward" button shortly and the red light changes to a steady
blue.
5. Now, press "Volume +" or "Volume -" to increase or reduce sensitivity. Every time
you press the Volume buttons the RED light will flash for confirmation. When you
reach the end of the upper and lower limit, the RED light will not flash.
6. Press again the "Backward" button shortly; the Blue light will flash several times, in
order to let you know the selected sensitivity:
One flash = VOX disabled
Twice = low sensitivity
3 times= normal sensitivity
4 times= high sensitivity (default setting)
5 times = Highest sensitivity
The light indicator is now back to steady RED ("Set up mode") and the changes
are confirmed
7. If needed, you can adjust again the sensitivity repeating the steps from point 1,
otherwise exit the Setting mode by double clicking the "Middle" button. Once the
red light turns off, the blue led starts blinking. Now you can use your Midland BTX2
PRO
13