Main Features; Technical Specifications Of Midland Btx2 Pro; Charging Batteries; Unit And Fixing System Description - Midland BTX2 PRO Guide D'utilisation

MIDLAND BTX2 PRO
Multi rider intercom system
Midland BTX2 PRO is an intercom system solution with conference communication for
motor cyclists.The design is very slim and aerodynamic, all the main functions are easy
to operate thanks to the three big buttons placed on the front of the unit. Midland BTX2
PRO is fixed on the helmet using the adhesive plate or the screw mounting clamp. Thanks
to the audio kit with ultra slim speakers you can enjoy high quality stereo music while
riding.

Main features

› Intercom "one to one" up to 1 Km distance.
› Conference 4 people
› Connect up to 4 people for "one to one" intercom communication
› Talk2All feature to connect other brand intercom
› FM Radio Stereo with RDS
› Music Share (Driver and Passenger)
› Connect your phone to receive and place phone call and listen to stereo music
› Support for 2 phones
› Connect your GPS for voice street indications
› Connection for PMR466 radio with internal or external Bluetooth
› AUX wired connection for MP3 player (optional cable)
› Setup and Firmware update via USB connection to a PC
Midland BTX2 PRO is available in two versions:
› Single Midland BTX2 PRO Intercom kit with one unit only
› Twin Midland BTX2 PRO Intercom kit with with two units
Depending on the model purchased, the package contains the following parts:
Midland BTX2 PRO single
› 1 BTX2 PRO communication unit
› 1 Slide-in mounting kit with two Hi-Fi stereo speakers
› 1 microphone with boom and 1 wired microphone
› 1 plate with bi-adhesive strip to fix the unit onto the helmet
2
› 1 USB cable
Midland BTX2 PRO Twin
› 2 BTX2 PRO communication units
› 2 Slide-in mounting kit with two Hi-Fi stereo speakers
› 2 microphones with boom and 2 wired microphones
› 2 plates with bi-adhesive strip to fix the unit onto the helmet
› 1 USB cable with with double plug
The units included in the TWIN kit are already paired on Middle button and therefore can
be immediately used in Intercom mode.

Technical specifications of Midland BTX2 PRO

General:
› Bluetooth ver. 4.2 Stereo (Handsfree/A2DP/AVRCP protocol)
› Frequency: 2.4 GHz - Max power 100mW
› AGC system automatically controls the volume in relation to background noise
› Voice (VOX) or manual communications activation
› Manual controls to enable: telephone, intercom and wire connection
› Fully waterproof
› Lithium battery with 30 hours talk time
› Recharge time: app. 2 hours
Bluetooth connections:
With identical device for Rider to Pillion or Bike-to-Bike Intercom mode, up to a ma-
ximum distance range of 1Km without obstructions and interferences (the riders must
be always in sight).
Bluetooth devices:
› Mobile phone with MP3 player Stereo (A2DP protocol) and GPS navigator
› PMR446 transceivers (with built-in or external Bluetooth connection) for group
bike-to-bike communications
Wire connections:
› For stereo audio input like iPod/MP3 player (with optional cable)
Attention: Midland BTX2 PRO is designed to withstand rain and water. However, if it is
raining, always verify that the rubber cap protecting the recharging sockets is fully fitted.
www.midlandeurope.com

Charging batteries

Attention: Make sure that the unit is fully charged before use. Allow at least 3 hours for a
full charge before using the unit for the first time.
Charge the unit by inserting the wall-charger into the charging socket (lift the rubber
cover to insert the plug). The red LED on the unit will start flashing when charging
begins.
Allow the headset to charge until the unit stops flashing or the blue LED turns on.
When the charge is complete (the red LED is not flashing), release the headset from
the charger. Normally, after the first time, it takes 2 hours for a full charge.
Attention: every time the micro USB recharging plug is inserted (or detached), the device
is automatically turned off. To use it while it is in charge, you should turn the device on
with the plug already inserted.

Unit and fixing system description

BTX2 PRO description
The BTX2 PRO has five buttons on the front; the main three big buttons are multi
functions buttons: the Forward (on the left), the middle button and the Backward (on
the right), the two squared buttons are the Volume + and Volume -.
Volume - Volume +
LED
Forward Middle Backward
Description of the wired connections
On the bottom of the unit you can find the Charger jack that enables to recharge the
unit using a standard microUSB power supply
The same micro USB charger plug can be used to connect an audio source, like a stereo
www.midlandeurope.com
iPod/MP3 player;
Attention: you need an optional AUX cable not included in the box.
Charger plug
Description of the audio kit
The audio system includes two ultra-flat stereo speakers and two interchangeable
microphones, which are both supplied with a bracket and wired connection. The mini
connector on the microphone allows you to choose the microphone that best suits the
helmet you are using.
Fixing the stereo speakers
The two stereo speakers have a Velcro/adhesive strip that aids their fixing into your
helmet. Beware not to completely cover your ear with the speakers, you must always
be able to listen to the traffic sound and your indicators.
The microphone can be fixed onto the helmet in two ways:
Boom Microphone
Place the section with the Velcro/adhesive strip between the padding and the rigid co-
ver of the helmet, so that the microphone is correctly positioned in front of your mouth
3