How To Pair The Midland Btx2 Pro To More Than Two Units; Conference - Midland BTX2 PRO Guide D'utilisation

Voice activation (VOX)
Simply say something, after some seconds the communication will be opened and will
remain active for the time you are talking. If there is no conversation the intercom will
be closed after 40 seconds. If needed you can close the intercom manually without
waiting 40 seconds (just press the middle button).
If needed, you can disable the VOX feature simply by pressing the Backward button
for 7 sec. A voice announcement will advise you when the VOX is disabled. To turn the
VOX on again, just press the same button and a voice announcement will advise you
that the VOX is now active. This setting is remembered also if you turn off the unit.
Attention: The Voice activation (VOX) can open the intercom communication only to the
unit that was paired with the Middle button. If you choose to use a different button (Forward
or Backward ), you will be able to active the intercom only manually.
Adjusting the volume
Your Midland BTX2 PRO uses AGC technology, which automatically adjusts the liste-
ning volume in relation to background noises.
However, it is also possible to manually adjust the volume by means of the "Volume
+" and "Volume -"buttons. The volume setting is indipendent for each audio source:
intercom, stereo music, phone call, FM radio.
Attention: volume can be adjusted only when an audio connection is active.
Set up of the AGC system
To adjust the sensitivity of the AGC system you can use the "BT UPDATER" Pc
Software or the smartphone "BT SET-APP" application. You can choose different set
up based on your motorbike type (naked, touring, sport) or if you are riding as a pas-
senger. You can disable the AGC system pressing "Volume +" and "Volume -" togheter
for 3 sec.

How to pair the Midland BTX2 PRO to more than two units

One Midland BTX2 PRO unit can be paired to maximum three other BT units, that
means four in total.
The Midland BTX2 PRO has three main buttons (Forward, Middle and Rear). It is up to
you which button use to pair and activate the "Intercom", you are totally free to choose
the button you like more.
6
Rider 1
Rider 3 Rider 2
Passenger
The same button you will use to pair the unit will be also used to open/close the inter-
com communication. For example you can pair your passenger to the Middle button
and other motorbikers to the Backward and Forward button. Everytime you open the
"Intercom" connection to one person, the previous connection will be closed.
The connection is not a "chain", when two persons are talking it is not possible to break
(interrupt) the communication by one of the other units.
Pair the Midland BTX2 PRO to another Midland BTX2 PRO unit
To pair the Midland BTX2 PRO to another Midland BTX2 PRO unit, you must first
enter the setup mode:
1. Turn off the unit
2. Press and hold down the middle button about 7 sec., until the Red light is on per-
manently.
3. Now press the Middle or the Backward or the Forward button for 3 seconds. The
Blue and Red lights will flash.
4. Do the same procedure on the other unit, when successfully paired, each unit will
have the Blue light on for one second and then go back to the setup mode (Red
light always on).
5. Now the pairing procedure is complete, you can go on pairing other units on diffe-
rent button or just exit the setup mode to start using the units:
6. Double click on the Middle button, the Red light will turn off and the Blue light will
start flashing.
You can use now your BTX2PRO.
www.midlandeurope.com
How to use the Intercom with more than two units
To use the intercom feature, be sure that all the units are turned on and correctly paired
together.
Manual activation in Intercom mode
Press the button corresponding to the unit you would like to communicate with. After
some seconds the intercom communication will open.
The communication remains active until you press again the same button. To quickly
open the intercom to another person, just press the button corresponding to the other
unit, the intercom will be automatically closed and the new connection will be opened.
Voice activation (VOX)
The voice activation feature can open the intercom only to the unit paired to the Midd-
le button. While no other communication is open, simply start talking and the commu-
nication will be opened and remain active for all the time you are talking. If there is no
conversation the intercom will be closed after 40 seconds. If needed you can close the
intercom manually without waiting 40 seconds, pressing the Middle button.
If needed, you can disable the VOX feature simply by pressing the Backward button
for 7 sec. A voice announcement will advise you when the VOX is disabled. To turn the
VOX on again, just press the same button and a voice announcement will advise you
that the VOX is now active. This setting is remembered also in you turn off the unit.
Hint: this feature is very useful when you have a specific person that you like to talk to more
often (for example your passenger). In this way you don't need to press a button to open
the communication.
Unit already busy in a conversation
If you try to open an intercom connection to another person that is already talking with
some one else (or is in a middle of a phone conversation), you will hear a "busy" double
beep tone. Just wait sometime and try again, maybe this time the "line" is not busy.
The person who is called, will be advised that someone is trying to call and will hear a
voice announcement with the number of the button from which the request is coming.
In this way as soon as the first conversation is over, the person can easily contact the
caller by opening the intercom of the specific button number (indicated by the voice
announcement).
www.midlandeurope.com
3
1
2

Conference

The "Conference" mode allows the communication with four people simultaneously.
The Midland BTX2 PRO unit can work as usually, with "one to one" communication up
3
1
2
to 4 people ("classic" Intercom mode) or with 4 people conference intercom (Confe-
rence mode).
How to use the conference mode
First of all you need to pair all the units in a "chain" mode, second the "Conference"
feature must be active on all the units paired.
Pairing
To use the conference mode you need to pair all the units in a "chain" configuration.
The BWD button of the first unit must be paired to the FWD button of the second
unit. The BWD button of the second unit must be paired to the FWD button of the
third unit and so on, till the fourth!
1 3
2 4
The first and the last unit must not be paired together (the chain must stay open).
The unit number 1 can talk to the last unit (number 4) only "through" the unit number
2 and number 3. That means to have the conference with four people, all the unit must
have the intercom open.
7