Maximum Distance; How To Pair Two Midland Btx2 Pro Units; Set Up Of The Agc System; How To Pair The Midland Btx2 Pro To More Than Two Units - Midland BTX2 PRO Guide D'utilisation

Maximum Distance

You can reach 1 Km intercom distance if you are in line of sight without obstructions and
interferences (the riders must be always in sight).

How to pair two Midland BTX2 PRO units

The two units supplied in the same Midland BTX2 PRO box, are already paired and ready
to use, which mean you don't need to perform this procedure. The units are already pai-
red using the Middle button. If the devices are not part of the same kit, or the units have
been purchased separately, you need to first pair it in order to use it.
To pair the Midland BTX2 PRO to another Midland BTX2 PRO unit
To pair the Midland BTX2 PRO to another Midland BTX2 PRO unit, you must first enter
the setup mode:
1. Turn off the unit
2. Press and hold down the middle button about 7 sec., until the Red light is on perma-
nently.
3. Now press the Middle button for 3 seconds. The Blue and Red light will flash.
4. Do the same procedure on the other unit. When successfully paired, each unit will have
the Blue light on for one second and then go back to the setup mode (Red light always
on).
5. Now the pairing procedure is complete, you just need to exit the setup mode before
you can use the units.
6. Double click on the Middle button, the Red light will turn off and the Blue light will start
flashing.
You can use now your Midland BTX2 PRO
Attention: remember to switch off all the other Bluetooth device that are not part of the pairing
procedure, only the two devices involved in the pairing must be turned on.
How to use the Intercom with two units
To use the intercom feature, be sure that both units are turned on and correctly paired
together.
Manual activation
Press the Middle button on one of the two units in "Intercom" mode. Communication is
22
enabled and remains active until you press again the middle button. The intercom need
some seconds to activate, you will hear a beep tone when the intercom is open.
Voice activation (VOX)
Simply say something, after some seconds the communication will be opened and will
remain active for the time you are talking. If there is no conversation the intercom will be
closed after 40 seconds. If needed you can close the intercom manually without waiting
40 seconds (just press the middle button).
If needed, you can disable the VOX feature simply by pressing the Backward button for
7 sec. A voice announcement will advise you when the VOX is disabled. To turn the VOX
on again, just press the same button and a voice announcement will advise you that the
VOX is now active. This setting is remembered also if you turn off the unit.
Attention: The Voice activation (VOX) can open the intercom communication only to the unit
that was paired with the Middle button. If you choose to use a different button (Forward or
Backward ), you will be able to active the intercom only manually.
Adjusting the volume
Your Midland BTX2 PRO uses AGC technology, which automatically adjusts the liste-
ning volume in relation to background noises.
However, it is also possible to manually adjust the volume by means of the "Volume +"
and "Volume -"buttons. The volume setting is indipendent for each audio source:
intercom, stereo music, phone call, FM radio.
Attention: volume can be adjusted only when an audio connection is active.

Set up of the AGC system

To adjust the sensitivity of the AGC system you can use the "BT UPDATER" Pc Softwa-
re or the smartphone "BT SET-APP" application. You can choose different set up based
on your motorbike type (naked, touring, sport) or if you are riding as a passenger. You can
disable the AGC system pressing "Volume +" and "Volume -" togheter for 3 sec.

How to pair the Midland BTX2 PRO to more than two units

One Midland BTX2 PRO unit can be paired to maximum three other BT units, that me-
ans four in total.
www.midlandeurope.com