Emergency Stop Light; Setup And Special Configurations - Midland BTX2 PRO Guide D'utilisation

Enabling/disabling the wired input
If needed the wired input can be enabled or disabled:
Enabling/Disabling: Make a Long press (3 sec.) on the "Forward" and "Middle" button
(you will hear one audio beep tone for enabling confirmation and two audio beep tones
for disabling). This setting is rembered also after turning On/Off the unit.
Wired audio in background
The audio from the wired connection can be in background to your Intercom or Phone
communication. By default this option is ON. Please refer to the paragraph "Wired con-
nection always in background" below to disable it.
Note that is not possible to have the wired audio source in background to the FM radio.

Emergency Stop light

On the back of your BTX2 PRO mounting kit you have an ultra bright
LED emergency stop light. Every time you make a full brake, the stop
light will turn ON to give an extra alert to the drivers behind you. In case
you need to turn it OFF temporarily (for example when you ride with a
passenger), just press long "Backward" and "Forward" buttons togheter
while in "Phone" or "Intercom" mode (a voice announcement will confirm
the status). The unit will remember the last setting used, that means you
need to turn ON manually the stop light pressing again "Backward" and
"Forward" buttons togheter.
Attention: By default the stop light is OFF

Setup and special configurations

Resetting all paired devices
Sometimes you may find it necessary to delete all the pairing references stored in the Mi-
dland BTX2 PRO unit (reset operation).
To perform this operation you must first enter the setup mode:
› Turn off the unit
› Press and hold down the "Middle" button 7 sec., until the Red light is on permanently.
› Then simultaneously press and hold down the "Volume +" and "Volume –" buttons for 3
30
seconds. The Blue Light will be lit on for 1 sec and than back to steady RED.
› Double click on the "Middle" button to exit the "Setup" mode.
This procedure deletes all the paired Bluetooth devices stored in the memory and it is the-
refore possible to start a new "clean" pairing session.
Back to factory setting
Sometimes you may find it necessary to go back to the factory setting, to reset all the
changes/setup already made and have a "clean" unit.
To perform this operation you must first enter the setup mode:
› Turn off the unit
› Press and hold down the "Middle" button about 7 sec., until the Red light is on perma-
nently.
› Then simultaneously press and hold down all the three buttons "Forward"-"Midd-
le"-"Backward" for 3 seconds. The Blue Light will be lit on for 1 sec and than back to
steady RED.
› Double click on the "Middle" button to exit the "Setup" mode and use the Midland BTX2
PRO
Adjusting/ Disabling the VOX feature (Intercom and telephone)
The Intercom feature can be enabled both manually and vocally (VOX). The VOX activa-
tion is influenced by the helmet type, the background noise and therefore by the speed.
For optimum results, it is possible to choose one of the following four microphone sensi-
Stop Light
tivity levels: high, medium, low and very low. The default setting of Midland BTX2 PRO is
"High". It is also possible to disable the VOX feature in order to activate the Intercom and
phone call answering features in manual mode only.
Adjusting the sensitivity of the (VOX)
To perform this operation you must first enter the setup mode:
1. Turn off the unit
2. Press and hold down the "Middle" button about 7 sec., until the Red light is on per-
manently.
3. Your Midland BTX2 PRO is now in "Set up mode".
4. Press the "Backward" button shortly and the red light changes to a steady blue.
5. Now, press "Volume +" or "Volume -" to increase or reduce sensitivity. Every time you
press the Volume buttons the RED light will flash for confirmation. When you reach
www.midlandeurope.com