Set Up Of The Agc System; Compatibility With Midland Bt Line Units; Talk 2 All - Universal Intercom With Different Brand Unit; Pairing The Btx1 Pro To Bluetooth Devices - Midland BTX1 PRO Guide D'utilisation

If needed, you can disable the VOX feature simply by pressing the Backward button for
7 sec. A voice announcement will advise you when the VOX is disabled. To turn the VOX
on again, just press the same button and a voice announcement will advise you that the
VOX is now active. This setting is remembered also if you turn off the unit.
Adjusting the volume
Your Midland BTX1 PRO uses AGC technology, which automatically adjusts the liste-
ning volume in relation to background noises. However, it is also possible to manually
adjust the volume by means of the "Volume +" and "Volume -"buttons.
The volume setting is indipendent for each audio source: intercom, stereo music, phone
call, FM radio.
Attention: volume can be adjusted only when an audio connection is active.

Set up of the AGC system

To adjust the sensitivity of the AGC system you can use the "BT UPDATER" Pc Softwa-
re or the smartphone "BT SET-APP" application. You can choose different set up based
on your motorbike type (naked, touring, sport) or if you are riding as a passenger. You
can disable the AGC system pressing "Volume +" and "Volume -" togheter for 3 sec.

Compatibility with Midland BT line units

The BTX1 PRO is compatible with BTX2 PRO, BT Next PRO, BT Next Conference,
BTX2 FM and BTX1 FM.
When paired the max distance of the intercom is defined from the lower possible.
The BTX1 PRO is compatible with the previous line of Midland BT (BT Next, BTX2 and
BTX1) only if updated to firmware version 2014 or later.

Talk 2 All - Universal Intercom with different brand unit

Thanks to the "Talk2 All - Universal Intercom" feature it is now possible to pair your BTX1
PRO to a different brand intercom available on the market.
1. On the BTX1 PRO enter the setup mode: (With the unit OFF press and hold down
the Middle button about 7 sec., until the Red light is on permanently.
2. Press the "Forward" button for 3 seconds, the Red and Blu LED light will flash slowly.
3. On the other intercom (not Midland brand) follow the procedure to pair to a phone.
6
Talk2All - Universal Intercom
Not Midland Unit
Attention: remember to switch OFF all the other Bluetooth device during the pairing proce-
dure, only the two devices involved in the pairing must be turned on.
If successfully paired the red/blue light will stop flashing and the blu light will slowly flash
instead.
To open/close the "Universal Intercom" communication from the BTX1 PRO press
"Forward" button (in "Intercom" mode)
On the other intercom just press the phone redial button.
Maybe it will be necessary to press the dial button two times, depending on the model
of the not Midland intercom.
Attention: when using this configuration, the other intercom (not Midland brand) will be able
to be paired to a phone only if two phones are supported.

Pairing the BTX1 PRO to Bluetooth devices

The BTX1 PRO Conference unit can be paired to other Bluetooth devices, like Pho-
ne, GPS Navigator or PMR446 Radio with built-in or external Bluetooth (dongle).
The pairing procedure must be done using the "Volume +" or the "Volume -" buttons.
› Pairing to the "Volume +" button: for Phone with music A2DP stereo, GPS Naviga-
tor with A2DP audio or external mono/Stereo A2DP dongle.
› All devices paired to "Volume +" button have higher priority and will interrupt all the
other communications (like Intercom, FM Radio and Music).
› Pairing to the "Volume -" button: for a second phone with mono audio (Hands Free
Protocol) for GPS navigators/ Radar detector and other devices with mono audio.
When a device is paired to the "Vol +" or "Vol –" buttons the "Phone" mode is activated.
www.midlandeurope.com