Operation; Direct Control - IMG STAGELINE DMX-3216 Mode D'emploi

to be assigned. The LED above the appropriate
GB
jog wheel (19, 22) will light up to indicate the cur-
rent selection.
6) Keep the button MODE pressed and also press
the button (1) above the control for the corre-
sponding channel. Since a unit can have up to
32 channels, four channels are assigned to each
button (levels A – D) [
sliders]. The LEDs A – D (2) indicate the current
level. Use the button PAGE (3) to switch to
another level.
All LEDs will flash briefly to confirm the
assignment; the number of the channel
assigned will appear on the display.
Repeat steps 5 and 6 for the other movement direc-
tion.
7) To delete the assignments, press the buttons
MODE and DEL (21) at the same time. All
LEDs will flash briefly to confirm the deletion;
ASS00 00 will appear on the display.
8) To switch to the direction reversal option, press
the buttons FINE and MODE at the same time.
The LED REVERSE (9) will light up and the dis-
play will indicate the current channel reversal of
the unit selected, e. g.
nel 2 is reversed, the TILT channel is not
reversed.
9) Use the button
ment (PAN) or the tilt movement (TILT) is to be
reversed. The LED above the appropriate jog
wheel will light up to indicate the current selec-
tion.
10)Keep the button MODE pressed and also press
the button (1) above the control for the corre-
sponding channel.
All LEDs will flash briefly to confirm the
assignment; the number of the channel reversed
will appear on the display.
If required, repeat steps 9 and 10 to reverse the
other movement direction.
11)To delete the reversions, press the buttons
MODE and DEL (21) at the same time. All
LEDs will flash briefly to confirm the deletion;
RES00 00
will appear on the display.
If required, repeat steps 3 to 11 for further units.
12)To exit the programming mode, keep the button
PROGRAM / REC (10) pressed for 3 s. The LED
next to the button will extinguish.
20
lettering right above the
RES02 00 = PAN chan-
or to define if the pan move-
5

Operation

Use the POWER switch (33) to switch on the con-
troller. The display briefly indicates the firmware
version. Then Fixture Select
display, prompting the user to select a light effect
unit (fixture). It is possible to call up scenes and
programs the user has created with the DMX-3216
and to call up predefined movement patterns; how-
ever, the light effect units can also be directly con-
trolled by means of the sliders (4).
After operation, use the POWER switch to
switch off the controller. If the controller is not used
for a longer period of time, disconnect the power
supply unit from the mains socket; the power sup-
ply unit will have a low power consumption even
when the controller is switched off.

5.1 Direct control

1) The LED above the button SCENE / FIXTURE
(5) must light up. If it does not light up or if it
flashes, press the button.
2) Use the number buttons (17) to select the unit to
be controlled. Multiple units may be selected at
the same time if they have the same channel
functions and if they are to be controlled in the
same way. When a unit has been selected, the
LED above the appropriate number button will
light up. To deselect a unit, press its number but-
ton again.
3) Use the sliders (4) to make the adjustments for
the appropriate channels. The DMX value sup-
plied for the respective channel will appear on
DATA 255
the display, e. g.
Since a unit can have up to 32 channels, four
channels are assigned to each slider. The level
selected (A – D) defines the channel to be con-
trolled ( lettering right above the sliders). The
LEDs A – D (2) indicate the current level. Use the
button PAGE (3) to switch to another level.
To set all channels of all units to the value
zero at the same time, use the button RELEASE/
CLEAR (23).
4) For units with controllable movements (e. g.
moving head, scanner), the jog wheels PAN (19)
and TILT (22) can be used for a more convenient
control of the pan and tilt movements.
For a more precise control, press the button
FINE (18) so that the LED next to the button
lights up. The values will then be changed in
steps of 1.To exit the precise-control mode,
press the button again.
Direct control will always take priority over pro-
grammed scenes (SCENE), automatic programs
(CHASE) and movement patterns (MOVEMENT).
If a channel is directly controlled while a program or
appears on the
.