Useful Advice - grandimpianti WFEC 6 Mode D'emploi

www.groupdynamics-laundry.com
sales@groupdynamics.lv
In standard programming, only the last rinse
step does not drain the water, so that the last
spin may be started with water in the tub,
which will be drained as soon as the machine
has distributed the wash load.
Cool-down (F1)
As a rule at the end of a high-temperature
wash cycle (above 60°C) soft water is taken
in in order for drum inside temperature to
decrease gradually. When F1 is set to 1, this
action is not performed.
Cool-down (F1)
As a rule at the end of a high-temperature
wash cycle (above 60°C) soft water is taken
in, in order for drum inside temperature to
decrease gradually. When F1 is set to 1, this
action is not performed.
Value Function
0 Normal (default)
1 NO cool-down
This function can be programmed cycle by
cycle.
Shorter spinning (F2)
Final spinning can be set to 1 minute or
eliminated altogether. Effective spinning
means the maximum high-speed time. The
speeding up is not affected by this function.
Value Function
0 Normal (default)
1 1 minute spinning
2 No spinning
This function can be programmed cycle by
cycle.
No prewash (F3)
When this function is enabled the prewash
step is excluded.
Value Function
0 Normal (default)
1 No prewash
This function can be programmed cycle by
cycle.
Cycle deferred start (F4)
Postpones the start of a wash cycle and
determines cycle delay.
If the value assigned to this function is other
than zero, as soon as the programming session
is exited the time DISPLAY will blink the
hours and the temperature will blink the
minutes whereas the cycle display will read
the selected wash cycle.
To start the countdown, just press the START
push-button: the displays will be lit
continuously.
As soon as the countdown, is over the cycle
will start automatically and the displays will
resume their usual functions.
Before the START push-button is pressed
and during the count-down all keys are
enabled.
IMPORTANT !!!
Time is displayed in the "HH.MM"format.
H stands for hours and M for tens of minutes.
Unit: hours and minutes
h h
Range: 00 00'...23 50'
(00.00...23.50)
Resolution: 10 minutes
(0.1)
Default: 00 h 00'
Details:
When pressed, the START key excites the
CYCLE relay and the door is automatically
locked.
If the door is not closed correctly, the "door"
alarm will warn the user. If the door fails to
be locked, alarm "E6" will appear.
In this case the machine will not work until
the problem is solved and the START is
pressed once again.
If a deferred start is aborted - by entering the
programming mode and setting F4 to 00.00
- the door will be automatically unlocked.
Enable/Disable buzzer (F5)
This function enables/disables the buzzer,
which can be completely eliminated from all
cycles except for alarm sounds.
Value Function
0 Normal (default)
1 No buzzer
Changes to this function will affect all cycles.
Changing heating temperature (F6)
This function lowers maintain temperature
by 10°C.
If a wash temperature in a cycle is normally
90°C, it can be set to 80°C by altering this
function.
Value Function
0 Normal (default)
1 Temperature decrease by 10°C.
Enabling drum rotation during take-in
and drain (F7)
When executing particularly delicate wash
diagrams it is appropriate to keep the drum
still while the machine is taking in or draining.
Value Function
0 drum action enabled
1 no drum action during take-in/drain
This function is to be enabled for every
single cycle.
Caution! The drum still turns once
clockwise and once counterclockwise
before pausing and waiting for the
prescribed water level to be reached.
Adjustment of heating hystheresis (F8)
Setting this parameter it is possible to adjust
temperature precision at maintain steps. In
other terms, it is possible to determine when
the heating must go on again after the setting
was reached and then the temperature
dropped naturally.
The higher the precision, the more often
heaters go on and off.
19
Value Function
2 the heaters get back on 2°C below
the temperature setting.
3 the heaters get back on 3°C below
the temperature setting.
4 4°C° below the temperature setting.
5 5°C° below the temperature setting.
6 6°C° below the temperature setting.
Assuming that this function is set to value 3
for a 60°C cycle, the machine will heat the
water up to 60°C and then the heaters go off:
the heaters will go back on only when the
temperature drops to 57°, and will stay on
until the 60°C setting is reached again.
Viewing the time to the end of the cycle (F9)
It is possible to decide whether the time read
is the effective duration of the selected wash
diagram or an absolutely arbitrary value that
can be set. Caution! This reading is
nonetheless a reference and does by no
means influence the effective duration or
the features of the wash diagram, whatever
the value we may assign to it.
Value Function
0 The display reads the effective
cycle time
1 Arbitrary reading.
Thus the function " ti " is enabled, which is
to be configured with the values, expressed
in minutes that the display must read, for
each cycle.
Changes to this function will affect all cycles.
Enable cycles (Ci)
Stored cycles can be enabled/disabled singly,
i.e. using the SEL push-button, they can be
included/discarded from the list of those that
can be selected.
Value Function
0 Disables cycle
1 Enables cycle (default)
If all cycles should be disabled by mistake,
then the displays will read "CYCLE" after
programming is exited. Press PROG to solve
the fault and reset "Ci" correctly.
Attention!
Disabled cycles are NOT discarded and lost
but simply hidden from the user interface.
They can be added to the list of available
cycles at any time.

7.4 USEFUL ADVICE

Remember that loading 80% of the machine's
rated capacity provides better wash results.
Mind that more soap does not mean better
wash: on the contrary, using too much
washing powder leads only to unnecessary
pollution. The right amount of soap is
indicated by your supplier according to the
relevant water hardness.
Unless specifically advised against, the use
of the water economiser is warmly
recommended and so is the reduction of
maximum temperature, in order to curb water