Protective Circuit; 10 Specifications - Monacor PA-1120 Mode D'emploi

b) Start the announcement with the button
START/ STOP (72) . To stop the announce-
ment, press the button START/ STOP again .
c) With the button REPEAT/ STOP (71), an an-
nouncement can also be repeated several
times . Adjust the number of repeats and the
intervals on the insertion (see instructions of
this insertion) . To stop the announcement,
actuate the button REPEAT/ STOP again .
Notes:
1 . The announcement of storage M 6 may be locked
(see chapter 6 .4 .1, item 9) . If the switch MESSAGE
BANK is set to position 6 in this case, the an-
nouncement selected before is reproduced .
2 . If at least one zone button (4) is pressed at the
amplifier, after releasing the TALK button, the
announcement selected with the switch MESSAGE
BANK can be heard . To prevent this, leave a stor-
age location of the digital message insertion open
or cancel it and select this storage location with
the switch MESSAGE BANK .
4) The three LEDs POWER, SEND and BUSY (66)
give the following information:
POWER lights up when the amplifier is
switched on
SEND lights up when an announcement is
made via the microphone or a stored
announcement is called up
BUSY lights up with individual announce-
ments and with announcements
via other connected microphones
PA-1120RC .
9

Protective Circuit

The amplifier is provided with a protective circuit
against overload and overheating . If the protec-
tive circuit is activated, the LED PROT (22) lights
up and the amplifier is muted:
1 . for approx . 1 second after switching on
(switch-on delay)
2 . for approx . 1 second after switching off
3 . if the amplifier is overloaded
4 . if the amplifier is overheated; in addition, the
LED TEMP (20) lights up
If the LED PROT lights up during operation or if
it does not extinguish after switching on, switch
off the amplifier and eliminate the source of error .

10 Specifications

Model
Output power
Rated power
100 V outputs*
4 Ω outputs*
Max . output power
THD
Inputs
MIC / LINE CH 1 – CH 3
LINE CH 4 and CH 5
AMP IN
TEL PAGING
Extension insertion
Phantom power
Outputs
Speakers*
REC
PRE OUT
Frequency range
Equalizer
Bass
Treble
S / N ratio
Line
Mic
Ambient temperature
Power supply
Mains voltage
Power consumption
Emergency power supply:
Direct current consumption
Dimensions (W × H × D)
Rack spaces
Weight
* Either use the 100 V outputs
or the 4 Ω output!
All rights reserved by MONACOR
may be reproduced in any form or by any means for any commercial use.
PA-1120
5 × 100 W, however together
not more than 120 W
1 × 120 W
170 W
< 1 %
Input sensitivity, impedance; connection
2 .5 – 300 mV, 5 kΩ; XLR / 6 .3 mm jack, bal .
300 mV, 15 kΩ; RCA, unbal .
775 mV, 10 kΩ; 6 .3 mm jack, unbal .
250 mV, 5 kΩ; screw connection, bal .
250 mV, 10 kΩ, unbal .
17 V for CH 1 – 3, to be switched individually
5 × 100 V, 1 × 4 Ω
775 mV at 3 kΩ, unbal .
775 mV at 100 Ω, unbal .
55 – 16 000 Hz, −3 dB
±10 dB / 100 Hz
±10 dB / 10 kHz
> 80 dB (A weighted)
> 70 dB (A weighted)
230 V/ 50 Hz
340 VA
⎓ 24 V
15 A
482 × 133 × 352 mm
3 RS
13 kg
® INTERNATIONAL GmbH & Co. KG. No part of this instruction manual
PA-1240
5 × 100 W, however together
not more than 240 W
1 × 240 W
340 W
< 1 %
0 – 40 °C
230 V/ 50 Hz
630 VA
⎓ 24 V
27 A
482 × 133 × 352 mm
3 RS
14 kg
Subject to technical modification .
15