Nolan N44 Instructions D'utilisation page 9

Insert the VPS SX end into the left side frame inside the shell until you hear a click providing the fastening of the VPS (Fig. 13).
Repeat the same operation on the DX side.
Make sure the VPS operates correctly by activating and deactivating it according to the instructions above.
- I f the visor and/or VPS opening/closing mechanisms are damaged or malfunctioning, do not use the helmet
and contact immediately a Nolan authorized dealer.
• WIND PROTECTOR
This accessory allows improved helmet performance under certain conditions of use. The Wind Protector reduces
unpleasant infiltrations of air under the chin. See Fig. 14 for the assembly and disassembly.
• REMOVABLE INNER COMFORT PADDING
1. LINER DISASSEMBLY WITH ROLL NECK
1.1 Open the chin strap (see specific instructions), remove the roll neck flap from the cheek pad, pull the front part of the
left cheek pad towards the inside of the helmet to release the first snap fastener located on the left frame (Fig. 15).
Repeat the same operation on the right side of the helmet.
1.2 Release the left roll neck eyelet from the frame fixed to the outer shell (Fig. 16). Repeat the same operation on the right
side of the helmet.
1.3 Unhook the rear left fastening flap of the support attached to the edge of the inner shell and pull the comfort padding
lightly towards the inside, at the helmet neck-ring area (Fig. 18). Then repeat the same steps to remove the central
flaps as well as the right rear flap.
1.4 Hold the left front part of the liner and pull it upwards in order to remove the liner flap from the support fixed to the
polystyrene inner shell (Fig. 18). Then repeat the same steps for the central front and right flap.
1.5 Remove the right and left side flaps of the comfort padding (located between the inner and outer shells) by pulling
them towards the outside (Fig. 19).
1.6 Remove the chin straps from the liner (Fig. 20).
1.7 Completely remove the liner from the helmet.
2. LINER ASSEMBLY WITH ROLL NECK
2.1 Insert the liner correctly into the helmet and fit it well against the base.
2.2 Insert the chin straps into the slot of the left cheek pad in the liner (Fig. 20).
2.3 Insert the left front flap into the seat on the support fixed to the polystyrene inner shell
Insert the VPS SX end into the left side frame inside the shell until you hear a click providing the fastening of the VPS (Fig. 13).
Repeat the same operation on the DX side.
Make sure the VPS operates correctly by activating and deactivating it according to the instructions above.
- I f the visor and/or VPS opening/closing mechanisms are damaged or malfunctioning, do not use the helmet
and contact immediately a Nolan authorized dealer.
• WIND PROTECTOR
This accessory allows improved helmet performance under certain conditions of use. The Wind Protector reduces
unpleasant infiltrations of air under the chin. See Fig. 14 for the assembly and disassembly.
• REMOVABLE INNER COMFORT PADDING
1. LINER DISASSEMBLY WITH ROLL NECK
1.1 Open the chin strap (see specific instructions), remove the roll neck flap from the cheek pad, pull the front part of the
left cheek pad towards the inside of the helmet to release the first snap fastener located on the left frame (Fig. 15).
Repeat the same operation on the right side of the helmet.
1.2 Release the left roll neck eyelet from the frame fixed to the outer shell (Fig. 16). Repeat the same operation on the right
side of the helmet.
1.3 Unhook the rear left fastening flap of the support attached to the edge of the inner shell and pull the comfort padding
lightly towards the inside, at the helmet neck-ring area (Fig. 18). Then repeat the same steps to remove the central
flaps as well as the right rear flap.
1.4 Hold the left front part of the liner and pull it upwards in order to remove the liner flap from the support fixed to the
polystyrene inner shell (Fig. 18). Then repeat the same steps for the central front and right flap.
1.5 Remove the right and left side flaps of the comfort padding (located between the inner and outer shells) by pulling
them towards the outside (Fig. 19).
1.6 Remove the chin straps from the liner (Fig. 20).
1.7 Completely remove the liner from the helmet.
2. LINER ASSEMBLY WITH ROLL NECK
2.1 Insert the liner correctly into the helmet and fit it well against the base.
2.2 Insert the chin straps into the slot of the left cheek pad in the liner (Fig. 20).
2.3 Insert the left front flap into the seat on the support fixed to the polystyrene inner shell
9
9