Nolan N44 Instructions D'utilisation page 13

Casque
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

WARNING!!!
-
Make sure that the mechanisms are working properly. Rotate the peak upwards or downwards making sure
that the mechanisms hold it in the 2 different positions. If necessary, repeat the above-mentioned steps.
-
Do not use the helmet if the peak has not been assembled properly.
-
Should any of the side mechanisms be malfunctioning or damaged, please refer to a Nolan authorized dealer.
- When riding on the road, the peak HAS to be adjusted to the highest position (Fig. 28).
2. PEAK DISASSEMBLY
2.1 Push the peak upwards (Fig. 28).
2.2 Push the release lever of the mechanism completely upwards and, at the same time, pull the peak away from the
helmet (Fig. 27).
2.3 Release the release lever which should return downwards.
2.4 Follow the same steps on the other side of the helmet.
WARNING!!!
-
When using the helmet without the visor and/or without the peak, always assemble the side plates.
-
Do not remove the side mechanisms from the shell.
(Available as an optional accessory)
1. PINLOCK® INNER VISOR ASSEMBLY
1.1 Remove the visor.
1.2 Make sure that the inner surface of the visor is clean and check that the pin adjustment external levers are turned
inwards.
1.3 Place the Pinlock® inner visor on the visor. WARNING: The silicone-sealed profile of the Pinlock® inner visor should
be in contact with the inner surface of the visor.
1.4 Insert one side of the Pinlock® inner visor on one of the visor pins and hold it in position (Fig. 30).
1.5 Widen the visor and fasten the other side of the Pinlock® inner visor to the second pin (Fig. 31).
1.6 Release the visor.
1.7 Remove the protective film from the Pinlock® inner visor and check that the entire silicone-sealed profile of the inner
WARNING!!!
-
Make sure that the mechanisms are working properly. Rotate the peak upwards or downwards making sure
that the mechanisms hold it in the 2 different positions. If necessary, repeat the above-mentioned steps.
-
Do not use the helmet if the peak has not been assembled properly.
-
Should any of the side mechanisms be malfunctioning or damaged, please refer to a Nolan authorized dealer.
- When riding on the road, the peak HAS to be adjusted to the highest position (Fig. 28).
2. PEAK DISASSEMBLY
2.1 Push the peak upwards (Fig. 28).
2.2 Push the release lever of the mechanism completely upwards and, at the same time, pull the peak away from the
helmet (Fig. 27).
2.3 Release the release lever which should return downwards.
2.4 Follow the same steps on the other side of the helmet.
WARNING!!!
-
When using the helmet without the visor and/or without the peak, always assemble the side plates.
-
Do not remove the side mechanisms from the shell.
(Available as an optional accessory)
1. PINLOCK® INNER VISOR ASSEMBLY
1.1 Remove the visor.
1.2 Make sure that the inner surface of the visor is clean and check that the pin adjustment external levers are turned
inwards.
1.3 Place the Pinlock® inner visor on the visor. WARNING: The silicone-sealed profile of the Pinlock® inner visor should
be in contact with the inner surface of the visor.
1.4 Insert one side of the Pinlock® inner visor on one of the visor pins and hold it in position (Fig. 30).
1.5 Widen the visor and fasten the other side of the Pinlock® inner visor to the second pin (Fig. 31).
1.6 Release the visor.
1.7 Remove the protective film from the Pinlock® inner visor and check that the entire silicone-sealed profile of the inner
13
13

Publicité

Table des Matières
loading

Table des Matières