Nolan N44 Instructions D'utilisation page 11

lightly towards the inside, at the helmet neck-ring area. Then repeat the same steps to remove the central flaps as well
as the right rear flap. (Fig. 22).
4.3 Insert the roll neck into the liner by using its left, central and right slots (Fig. 21).
4.4 Insert the rear right, central and left flaps of the liner into the relevant support seats in the edge of the shell in the
helmet neck-ring area (Fig. 17). Push the flaps until they are fully hooked onto the support.
4.5 Hook the roll neck eyelet to the frame fixed to the outer shell, (Fig. 16) making sure that the frame's central air intake
is free.
4.6 Push the padding of the cheek pad in line with the snap fastener on its back by fastening it to its seat fixed to the shell.
Hook the roll neck flap to the cheek pad (Fig. 15).
NOTE: During ROLL NECK assembly and disassembly operations, make sure that the right and left side flaps of
the comfort padding are correctly placed between the inner and the outer shell (Fig. 19). If this is not the case,
repeat the steps 1.5 and 2.4.
WARNING!!!
- Remove the padding only when cleaning or washing is required.
- Never use the helmet if the inner comfort padding and the cheek pads have not been correctly and completely
fitted.
- Delicately hand-wash in lukewarm water (max. 30°C) and neutral soap.
- Rinse with cold water and allow drying at room temperature, away from direct sunlight.
- Never machine-wash the inner comfort padding.
- The inner polystyrene is an easily deformable material. It is apt to change or get partially destroyed to help
absorb shocks.
- Clean it with a damp cloth and allow it to dry at room temperature away from direct sunlight.
- Do not modify or alter the helmet's internal polystyrene components in any way.
- Never use tools or equipment of any sort to carry out the steps described above.
• SIDE PLATES
(Available as a standard feature if the helmet is in the version without visor and/or peak).
1. SIDE PLATES ASSEMBLY
1.1 Disassemble the visor from the helmet by following the specific instructions in this manual.
lightly towards the inside, at the helmet neck-ring area. Then repeat the same steps to remove the central flaps as well
as the right rear flap. (Fig. 22).
4.3 Insert the roll neck into the liner by using its left, central and right slots (Fig. 21).
4.4 Insert the rear right, central and left flaps of the liner into the relevant support seats in the edge of the shell in the
helmet neck-ring area (Fig. 17). Push the flaps until they are fully hooked onto the support.
4.5 Hook the roll neck eyelet to the frame fixed to the outer shell, (Fig. 16) making sure that the frame's central air intake
is free.
4.6 Push the padding of the cheek pad in line with the snap fastener on its back by fastening it to its seat fixed to the shell.
Hook the roll neck flap to the cheek pad (Fig. 15).
NOTE: During ROLL NECK assembly and disassembly operations, make sure that the right and left side flaps of
the comfort padding are correctly placed between the inner and the outer shell (Fig. 19). If this is not the case,
repeat the steps 1.5 and 2.4.
WARNING!!!
- Remove the padding only when cleaning or washing is required.
- Never use the helmet if the inner comfort padding and the cheek pads have not been correctly and completely
fitted.
- Delicately hand-wash in lukewarm water (max. 30°C) and neutral soap.
- Rinse with cold water and allow drying at room temperature, away from direct sunlight.
- Never machine-wash the inner comfort padding.
- The inner polystyrene is an easily deformable material. It is apt to change or get partially destroyed to help
absorb shocks.
- Clean it with a damp cloth and allow it to dry at room temperature away from direct sunlight.
- Do not modify or alter the helmet's internal polystyrene components in any way.
- Never use tools or equipment of any sort to carry out the steps described above.
• SIDE PLATES
(Available as a standard feature if the helmet is in the version without visor and/or peak).
1. SIDE PLATES ASSEMBLY
1.1 Disassemble the visor from the helmet by following the specific instructions in this manual.
11
11