Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
1.2 Place the left plate, identified with the letter "L" on the inside, on the left side mechanism of the helmet by centring the
side air intake of the plate on the mechanism itself (Fig. 24).
1.3 Slide the plate completely downwards (Fig. 25).
1.4 Repeat the same steps on the other side of the helmet using the right plate marked with letter "R" on the inside.
2. SIDE PLATES DISASSEMBLY
2.1 Slide the plate upwards (Fig. 25) and remove it from the side mechanism.
2.2 Follow the same steps on the other side of the helmet.
WARNING!!!
-
When using the helmet without the visor and/or without the peak, always assemble the side plates.
-
Do not use the helmet if the side plates have not been assembled properly.
-
Do not remove the side mechanisms from the shell.
-
Should any of the side mechanisms be malfunctioning or damaged, please refer to a Nolan authorized dealer.
• PEAK
(Available as a standard feature if the helmet is in the version without visor). (If this accessory/spare part is purchased
separately: this component is available in two different sizes according to shell size (SMALL or LARGE). Please ask
your Nolan dealer to assist you in selecting the right size.
WARNING!!!
- When riding on the road, the peak HAS to be adjusted to the highest position (Fig. 28).
1. PEAK ASSEMBLY
1.1 Disassemble the visor from the helmet by following the specific instructions in this manual.
1.2 Place the peak on the side mechanism centring the side air intake of the peak on the mechanism itself (Fig. 26).
1.3 Push the release lever of the mechanism completely upwards (Fig. 27) and, at the same time, push the peak against
the mechanism.
1.4 Release the release lever which should return downwards and make sure that the peak remains attached to the
mechanism.
1.5 Follow the same steps on the other side of the helmet.
The peak can be adjusted in two positions by turning it up or down Fig. 28-29).
1.2 Place the left plate, identified with the letter "L" on the inside, on the left side mechanism of the helmet by centring the
side air intake of the plate on the mechanism itself (Fig. 24).
1.3 Slide the plate completely downwards (Fig. 25).
1.4 Repeat the same steps on the other side of the helmet using the right plate marked with letter "R" on the inside.
2. SIDE PLATES DISASSEMBLY
2.1 Slide the plate upwards (Fig. 25) and remove it from the side mechanism.
2.2 Follow the same steps on the other side of the helmet.
WARNING!!!
-
When using the helmet without the visor and/or without the peak, always assemble the side plates.
-
Do not use the helmet if the side plates have not been assembled properly.
-
Do not remove the side mechanisms from the shell.
-
Should any of the side mechanisms be malfunctioning or damaged, please refer to a Nolan authorized dealer.
• PEAK
(Available as a standard feature if the helmet is in the version without visor). (If this accessory/spare part is purchased
separately: this component is available in two different sizes according to shell size (SMALL or LARGE). Please ask
your Nolan dealer to assist you in selecting the right size.
WARNING!!!
- When riding on the road, the peak HAS to be adjusted to the highest position (Fig. 28).
1. PEAK ASSEMBLY
1.1 Disassemble the visor from the helmet by following the specific instructions in this manual.
1.2 Place the peak on the side mechanism centring the side air intake of the peak on the mechanism itself (Fig. 26).
1.3 Push the release lever of the mechanism completely upwards (Fig. 27) and, at the same time, push the peak against
the mechanism.
1.4 Release the release lever which should return downwards and make sure that the peak remains attached to the
mechanism.
1.5 Follow the same steps on the other side of the helmet.
The peak can be adjusted in two positions by turning it up or down Fig. 28-29).
12
12
Publicité
Table des Matières
