Nolan N44 Instructions D'utilisation page 14

visor adheres to the visor.
1.8 Fit the visor in the helmet.
CHECKING AND ADJUSTING THE INNER VISOR STRETCHING
Check the correct system assembly by opening and closing the visor. Check that both visors are correctly fastened and
do not move. If the inner visor is not tightly fixed to the visor, move the external adjustment levers simultaneously upwards
to increase the stretch (Fig. 32). This operation must be carried out gradually. The maximum stretch is achieved when the
pin adjustment external levers are turned outwards.
WARNING!
The presence of dust between the two visors may produce scratches on both surfaces.
Scratched visors and inner visors may cause reduced visibility and must therefore be replaced.
Regularly check the correct stretching of the inner visor to prevent the same from moving and scratching both surfaces.
If the helmet visor fogs up and/or condensation forms between the visors, check both for system correct assembly and
stretching.
An excessive and early stretch of the inner visor may result in excessive adherence against visor surface and/or permanent
deformations with subsequent inability to perform following adjustments correctly.
The extended use under special weather conditions may reduce system performance and result in partial fogging and
problems of condensation on the inner visor. In this case, remove the inner visor from the helmet visor and dry it with dry
and lukewarm air to restore system efficiency.
Intense sweating /breathing, the use under particular weather conditions (low temperatures, and/or high humidity and/or
sudden changes in temperature or heavy rain) and intense and prolonged use may affect the performance of the system
and cause the fogging or formation of condensation on the inner visor.
In such cases, after using the helmet and to restore the system efficiency, remove the inner visor from the helmet visor
and let it dry with dry and lukewarm air. The same procedure must be applied to the helmet, in order to dry out humidity
in case it has formed up as a consequence of the conditions described above.
2. PINLOCK® INNER VISOR DISASSEMBLY
2.1 Remove the visor equipped with Pinlock® inner visor.
2.2 Widen the visor and release the Pinlock® inner visor from the pins (Fig. 31).
2.3 Release the visor.
visor adheres to the visor.
1.8 Fit the visor in the helmet.
CHECKING AND ADJUSTING THE INNER VISOR STRETCHING
Check the correct system assembly by opening and closing the visor. Check that both visors are correctly fastened and
do not move. If the inner visor is not tightly fixed to the visor, move the external adjustment levers simultaneously upwards
to increase the stretch (Fig. 32). This operation must be carried out gradually. The maximum stretch is achieved when the
pin adjustment external levers are turned outwards.
WARNING!
The presence of dust between the two visors may produce scratches on both surfaces.
Scratched visors and inner visors may cause reduced visibility and must therefore be replaced.
Regularly check the correct stretching of the inner visor to prevent the same from moving and scratching both surfaces.
If the helmet visor fogs up and/or condensation forms between the visors, check both for system correct assembly and
stretching.
An excessive and early stretch of the inner visor may result in excessive adherence against visor surface and/or permanent
deformations with subsequent inability to perform following adjustments correctly.
The extended use under special weather conditions may reduce system performance and result in partial fogging and
problems of condensation on the inner visor. In this case, remove the inner visor from the helmet visor and dry it with dry
and lukewarm air to restore system efficiency.
Intense sweating /breathing, the use under particular weather conditions (low temperatures, and/or high humidity and/or
sudden changes in temperature or heavy rain) and intense and prolonged use may affect the performance of the system
and cause the fogging or formation of condensation on the inner visor.
In such cases, after using the helmet and to restore the system efficiency, remove the inner visor from the helmet visor
and let it dry with dry and lukewarm air. The same procedure must be applied to the helmet, in order to dry out humidity
in case it has formed up as a consequence of the conditions described above.
2. PINLOCK® INNER VISOR DISASSEMBLY
2.1 Remove the visor equipped with Pinlock® inner visor.
2.2 Widen the visor and release the Pinlock® inner visor from the pins (Fig. 31).
2.3 Release the visor.
14
14