Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
and push it slightly downwards until it is completely locked. Follow the same steps for the central front and right flap (Fig. 18).
2.4 Insert the right and left side flaps of the comfort padding by pushing them between the inner and outer shells (Fig. 19).
2.5 Insert the rear right, central and left flaps of the liner into the relevant support seats in the edge of the shell in the
helmet neck-ring area (Fig. 17). Push the flaps until they are fully hooked onto the support.
2.6 Hook the roll neck eyelet to the frame fixed to the outer shell (Fig. 16) making sure that the frame's central air intake is free.
NOTE: Check the correct assembly of the liner front area by lifting and lowering the VPS. These movements should
be smooth. If this is not the case, repeat the steps 1.4 and 2.3.
2.7 Push the padding of the cheek pad in line with the snap fastener on its back by fastening it to its seat fixed to the shell.
Hook the roll neck flap to the cheek pad (Fig. 15).
3. ROLL NECK DISASSEMBLY
3.1 Remove the roll neck flap from the cheek pad, pull the front part of the left cheek pad towards the inside of the helmet
to release the snap fastener located on the left frame (Fig. 15). Repeat the same operation on the right side of the
helmet.
3.2 Release the roll neck eyelet from the frame fixed to the outer shell (Fig. 16). Repeat the same operation on the right
side of the helmet.
3.3 Unhook the rear left fastening flap of the support attached to the edge of the inner shell and pull the comfort padding
lightly towards the inside, at the helmet neck-ring area. Then repeat the same steps to remove the central flaps as well
as the right rear flap. (Fig. 17).
3.4 Remove the roll neck from the liner by using its left, central and right slots (Fig. 21).
3.5 Insert the rear right, central and left flaps of the liner into the relevant support seats in the edge of the shell in the
helmet neck-ring area (Fig. 22). Push the flaps until they are fully hooked onto the support.
3.6 Push the padding of the cheek pad in line with the snap fastener on its back by fastening it to its seat fixed to the shell
(Fig. 23).
4. ROLL NECK ASSEMBLY
4.1 Open the chin strap (see specific instructions), pull the front part of the left cheek pad towards the inside of the helmet
to release the first snap fastener located on the left frame (Fig. 23). Repeat the same operation on the right side of the
helmet.
4.2 Unhook the rear left fastening flap of the support attached to the edge of the inner shell and pull the comfort padding
and push it slightly downwards until it is completely locked. Follow the same steps for the central front and right flap (Fig. 18).
2.4 Insert the right and left side flaps of the comfort padding by pushing them between the inner and outer shells (Fig. 19).
2.5 Insert the rear right, central and left flaps of the liner into the relevant support seats in the edge of the shell in the
helmet neck-ring area (Fig. 17). Push the flaps until they are fully hooked onto the support.
2.6 Hook the roll neck eyelet to the frame fixed to the outer shell (Fig. 16) making sure that the frame's central air intake is free.
NOTE: Check the correct assembly of the liner front area by lifting and lowering the VPS. These movements should
be smooth. If this is not the case, repeat the steps 1.4 and 2.3.
2.7 Push the padding of the cheek pad in line with the snap fastener on its back by fastening it to its seat fixed to the shell.
Hook the roll neck flap to the cheek pad (Fig. 15).
3. ROLL NECK DISASSEMBLY
3.1 Remove the roll neck flap from the cheek pad, pull the front part of the left cheek pad towards the inside of the helmet
to release the snap fastener located on the left frame (Fig. 15). Repeat the same operation on the right side of the
helmet.
3.2 Release the roll neck eyelet from the frame fixed to the outer shell (Fig. 16). Repeat the same operation on the right
side of the helmet.
3.3 Unhook the rear left fastening flap of the support attached to the edge of the inner shell and pull the comfort padding
lightly towards the inside, at the helmet neck-ring area. Then repeat the same steps to remove the central flaps as well
as the right rear flap. (Fig. 17).
3.4 Remove the roll neck from the liner by using its left, central and right slots (Fig. 21).
3.5 Insert the rear right, central and left flaps of the liner into the relevant support seats in the edge of the shell in the
helmet neck-ring area (Fig. 22). Push the flaps until they are fully hooked onto the support.
3.6 Push the padding of the cheek pad in line with the snap fastener on its back by fastening it to its seat fixed to the shell
(Fig. 23).
4. ROLL NECK ASSEMBLY
4.1 Open the chin strap (see specific instructions), pull the front part of the left cheek pad towards the inside of the helmet
to release the first snap fastener located on the left frame (Fig. 23). Repeat the same operation on the right side of the
helmet.
4.2 Unhook the rear left fastening flap of the support attached to the edge of the inner shell and pull the comfort padding
10
10
Publicité
Table des Matières
