Ryobi RLT26CDS Manuel D'utilisation page 17

EN
FR DE ES
Prior to replacing the fuel cap, clean and inspect
Q
the gasket.
Immediately replace fuel cap and hand tighten.
Q
Wipe up any fuel spillage. Move 9 m away from
refueling site before starting engine.
Note: It is normal for smoke to be emitted from a new
engine during and after first use.
WARNING
Always shut off engine before fueling. Never add
fuel to a machine with a running or hot engine.
Move at least 9 m from refueling site before
starting engine. Do not smoke!
1 Litre +
2 Litres +
3 Litres +
4 Litres +
5 Litres +
STARTING AND STOPPING (Fig. 4)
WARNING
Never start or run the engine inside a closed or
poorly ventilated area; breathing exhaust fumes
can kill.
NOTE: Be sure to return the stop switch to the "I" (RUN)
position before trying to start unit.
To start a cold engine:
DO NOT squeeze the throttle trigger until the engine
starts and runs.
Lay the trimmer on a flat, bare surface.
„
PRIME - Press the primer bulb 10 times.
„
SET the start lever to the START position.
„
PULL the rope quickly and sharply straight up until
„
the engine starts.
Then squeeze the trigger to run.
„
NOTE: Squeezing and releasing the throttle trigger
releases the start lever to the RUN position.
If the engine stalls, set the start lever to the RUN position
" ". Then pull starter rope until the unit starts.
To start a warm engine:
Make sure carburettor is set to RUN position.
PULL the rope quickly and sharply straight up until the
engine starts.
To stop the engine:
Press and hold the switch in the stop " O " position until
the engine stops.
IT PT NL SV DA
English(Original instructions)
20 ml =
40 ml =
60 ml = 50:1 (2%)
80 ml =
100 ml =
NO FI HU CS RU
OPERATING THE TRIMMER (Fig. 5)
Hold the trimmer with the right hand on the rear handle
and the left hand on the front handle. Keep a firm grip
with both hands while in operation. Trimmer should be
held at a comfortable position with the rear handle about
hip height.
Always operate trimmer at full throttle. Cut tall
grass from the top down. This will prevent grass from
wrapping around the shaft housing and bump head
which may cause damage from overheating. If grass
becomes wrapped around the bump head, stop the
engine, disconnect the spark plug wire, and remove the
grass. Prolonged cutting at partial throttle will result in oil
dripping from the silencer.
CUTTING TIPS (Fig. 6)
When cutting make sure the cutter head is at a slight angle
as shown while still approximately parallel to the ground
surface. In tall grass cut from the top down to ensure the
moving parts do not get tangled with the long grass.
Move the head in steady strokes from right to left as you
work through the grass.
ADVANCING THE LINE (Fig. 7)
If the line becomes short, tap the head on the ground
as shown to extend more line. Take care not to 'crash' it
against a hard surface.
MAINTENANCE
WARNING
Use only original manufacturer's replacement
parts, accessories and attachments. Failure to
do so can cause possible injury, poor perfor-
mance and may void your warranty.
You may make adjustments and repairs described
„
here. For other repairs, have the trimmer serviced by
an authorised service agent.
Consequences of improper maintenance may
„
include excess carbon deposits resulting in loss of
performance and discharge of black oily residue
dripping from the silencer.
Make sure all guards, straps, deflectors and handles
„
are properly and securely attached to avoid the risk of
personal injury.
the cutting attachment must not rotate in idle mode. If
„
this requirement is not satisfied, the idle speed needs
adjustment (Fig.10) or the machine needs an urgent
maintenance by a qualified technician.
14 14
RO PL SL HR ET LT LV SK BG