Technical Data; Before Starting The Equipment - EINHELL AGILLO Traduction Du Mode D'emploi D'origine

Important! Due to the high risk of bodily injury
to the user, the equipment is not allowed to be
used to clean paths or to chop up tree and hedge
clippings. Similarly, the equipment must not be
used to level out high areas such as molehills. For
safety reasons, the equipment must not be used
as a drive unit for other work tools or toolkits of
any kind.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's construction and layout:
•
Lung damage if no suitable protective dust
mask is used.
•
Damage to hearing if no suitable ear
protection is applied.
•
Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
•
Injury and damage to property caused by
flying parts.
•
Cut injuries if no suitable safety clothing is
used.
Danger!
This electric power tool generates an
electromagnetic fi eld during operation. Under
certain circumstances this fi eld may actively or
passively impede medical implants. To reduce
the risk of serious or fatal injuries, we recommend
persons with medical implants to consult their
doctor and the manufacturer of the medical
implant prior to using the equipment.
Anl_Agillo_SPK7_USA.indb 16 Anl_Agillo_SPK7_USA.indb 16
EN

4. Technical data

Motor power supply: ............. 36 V
Speed n ................................... 6300 rpm (min
0
Cutting circle diameter of line ..Ø 12 in. (Ø 30 cm)
Line length ...........................................26 ft. (8 m)
Line diameter ............................0.08 in. (2.0 mm)
Cutting circle
diameter of blade .................Ø 10 in. (Ø 25.5 cm)
Protection class .................................................III
Weight ..................................... 13.4 lbs (6.09 kg)
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
•
Wear gloves.
•
Wear eye and hearing protection

5. Before starting the equipment

Caution! Carry out all the following assembly and
adjustment work without rechargeable batteries –
risk of injury. Wear protective gloves.
Inspect unit before each use. Replace damaged
parts. Check for fuel leaks. Make sure all
fasteners are in place and secure. Replace cutting
attachment parts that are cracked, chipped, or
damaged in any way. Make sure the cutting
attachment is properly installed and securely
fastened. Be sure the cutting attachment
shield is properly attached and in the position
recommended by the manufacturer. Use only
fl exible, nonmetallic line recommended by the
manufacturer. Never use, for example, wire or
wire-rope, which can break off and become a
dangerous projectile.
5.1 Fitting the guard hood (Fig. 3)
Remove the socket head screw from the guard
hood. Push the guard hood (15) onto the mount
on the motor housing as far as it will go and
screw it securely in place with the previously
removed socket head screw (Fig. 3). A blade (Fig.
2/ Item 14) on the underside of the guard hood
automatically cuts the cutting line to the optimum
- 16 -
(2x 18V)
)
-1
05.08.2019 10:37:30 05.08.2019 10:37:30