EINHELL AGILLO Traduction Du Mode D'emploi D'origine page 17

length. This is provided with a safety guard.
Remove the safety guard before starting work.
5.2 Fitting the additional handle (Fig. 4 – 4b)
Undo the handle screw (Fig. 2/Item 17) and
remove the thrust piece (Fig. 2/Item 5). Fit the
additional handle (16) into the holder (27) such
that the plastic ring (28) is in the groove on the
holder (27). Fasten the additional handle (16) to
the thrust piece (5) by re-tightening the handle
screw (17). Use the two supplied cable clips (26)
to fasten the protective tubing for the cable.
5.3 Fitting the long handle (Fig. 5)
Slot the top part of the long handle (6) into the
bottom part of the long handle (9). Screw the
handle connecting piece (7) to the bottom part of
the long handle with the union nut (8) on the top
part of the long handle.
5.4. Adjusting the angle of the additional
handle (Fig. 4a)
To adjust the additional handle to the optimum
working angle, slacken the handle screw (17).
Set the desired tilt of the additional handle (16).
Tighten the handle screw (17) again.
5.5 Removing/fi tting the cutting line unit
(Fig. 6)
Note: The equipment is supplied from the factory
ready for operation with the cutting line.
Warning! Take care not to cut yourself on the
cutting line cutter.
a) Removing the cutting line unit
Press the locking lever (12) forward and turn
the cutting line unit (29) clockwise at the
same time until the locking lever latches in
place. Turn the cutting line unit clockwise and
take it off the motor shaft.
b) Fitting the cutting line unit
Press the locking lever (12) forward and turn
the cutting line unit (29) counterclockwise
onto the motor shaft at the same time until
the locking lever latches in place. Turn the line
cutting unit on the motor shaft until it is tightly
secured. Check whether the cutting line
unit can rotate freely after you let go of the
locking lever. If this is not the case, have the
mechanism checked by an expert.
Anl_Agillo_SPK7_USA.indb 17 Anl_Agillo_SPK7_USA.indb 17
EN
5.6 Guard hood for use with the cutting blade
(Fig. 7)
Caution! The cutting line cover (30) must be
removed if you want to work with the cutting
blade. Take care not to cut yourself on the cutting
line cutter.
Slacken the two retaining screws (31) on the
cutting line cover.
Start at the side and carefully press in the lugs
and pull the cutting line cover (30) up and off .
5.7 Guard hood for use with the cutting line
(Fig. 7)
Caution! The cutting line cover (30) must be
fi tted if you want to work with the cutting line. Take
care not to cut yourself on the cutting line cutter.
Start at the side and press the lugs of the cutting
line cover back in and secure them with the two
screws (31).
5.8 Fitting/removing the cutting blade
The procedure for fi tting the cutting blade is
shown in Figs. 8a - 8c. Warning! Take care not to
cut yourself on the cutting blade.
a) Fitting the cutting blade
1. Fit the cutting blade (21) in place.
2. Fit the pressure plate (23) so that it is
completely on the cutting blade.
3. Fit the pressure plate cover (24).
4. Screw the size M10 hex nut (25) in place.
5. Press the locking lever (12) and lock the
motor shaft. Tighten the hex nut using the
multifunction tool (22).
6. Check whether the blade (21) can rotate
freely after you let go of the locking lever.
If this is not the case, have the mechanism
checked by an expert.
b) Removing the cutting blade
Press the locking lever forward and lock the motor
shaft. Unscrew and the hex nut and remove the
pressure plate cover, pressure plate and cutting
blade.
Each time before use, check the following:
•
That the equipment is in perfect condition and
that the safety devices and cutting devices
are complete.
•
That all screws are securely fastened.
•
That all moving parts move smoothly.
- 17 -
05.08.2019 10:37:31 05.08.2019 10:37:31