Mounting The License Plate Holder; Mounting The Frame Holder; Laying Electrical Cables; Mounting The Bicycles To The Rack - EUFAB CARLO PLUS Manuel De L'opérateur

For the wheel rails, there are two with a wide border (see photo) and two with a narrow border at one end so that they can be placed inside one another to form
a pair. Overlap these wheel rails at the end with the wide end over the narrow one. Place one rail pair on the front cross-bracket of the swing carrier and align it
with the drilled holes. For the inner drilled holes, use the lock screws M6 x 20, and washers and nuts M6, and first lightly screw the wheel rails in the middle to
the swing frame. Pull the wheel rails out far enough that you can use the outer drilled holes on the swing frame to affix the wheel rails. Here, secure the wheel
rails using the lock screws M6 x 40. Now tighten all of the screws on the wheel rails securely.
Fit the end caps onto the ends of the wheel rails.
Now push four wheel stoppers, two right and two left, from above onto the wheel rails. Make sure that the higher side of the wedge-shaped stopper points
towards the middle of the rack. Now insert the small tensioning strap through the middle opening of the wheel stopper and under the wheel rail on the opposite
side, and back through the middle opening. The remaining two straps are used later to correctly secure the bicycles.

5.1.4 MOUNTING THE LICENSE PLATE HOLDER

The mounting clips for securing the license plate are push-out parts
in the holder. Break out two of the clips. Slide the license plate into
the holder, then press the clips into the cut-out to secure the license
plate.

5.1.5 MOUNTING THE FRAME HOLDER

Frame holder, short
Undo the handle screw of the frame holder and rotate out fully. Open the cuff of the frame holder and place the inserts around the U-bracket at a position suita-
ble for your bicycle. Place the cuff around the inserts and push firmly together. Close the frame holder using the handle screw (but do not tighten).

5.1.6 LAYING ELECTRICAL CABLES

Secure the cables of the illumination unit with the help of cable ties below the swing carrier. Pay attention to ensure that, when unfolding and lifting the bicycle
rack, the cable is not trapped or damaged.
5.2 MOUNTING THE BICYCLE CARRIER TO THE TRAILER TOW BAR
Ensure that the trailer tow bar is undamaged, clean and free of grease.
The bicycle rack is placed horizontally on the tow bar from above.
Screw the bicycle rack using the screw M16 lightly into place, and align parallel to the rear of the vehicle. Now tighten the screw in such a way to ensure that
the rack is securely attached and can no longer be moved on the trailer tow bar. Evidence of pressure on the ball head are normal and do not represent a fault
nor will they affect the function of the tow bar.
Regularly check the firm seating of the rack on the trailer tow bar as well as the attachment of the bicycles to the rack. Also
regularly check the functions of the lighting system of your bicycle rack.

5.3 MOUNTING THE BICYCLES TO THE RACK

The first bicycle is placed in the first wheel rail (closest to the vehicle) and secured to the U-bracket with the
short frame holder. To do this, use the side of the frame holder with the tensioning strap to secure to the bicycle
frame. The wheels are secured by pushing the wheel stopper up to the wheel, placing the tensioning straps
around the wheel rim of your bicycle and tightening the straps.
CAUTION
The front wheel must also be secured to prevent it from turning using a small tensio-
ning strap. To do this, secure the front wheel to the rail again at a different position.
The second bicycle is usually placed in the second rail, facing the opposite direction to the first and secured
to the U-bracket with the long frame holder. The wheels are secured in the same way as for the first bicycle.
It may be necessary to offset the individual bicycles differently on the rack to ensure that the frame holders
may be correctly secured. Now secure the bicycles with the long safety strap. Wrap the safety strap through
the bicycle frames and the U-shaped bar and tighten.
The bicycle rack may not be used without this safety strap.
Frame holder, long
Clips
Cut-out for installation clips
Safety strap
9