Residual Risks; Know Your Product - Ryobi EMS254L Traduction Des Instructions Originales

Do not attempt to repair the laser device by yourself.
■
Do not attempt to change any parts of the laser device
■
by yourself.
Any repairs must only be carried out by the laser
■
manufacturer or authorized service agent.
Do not replace the laser with a different type.
■

rEsIdual rIsKs

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:
risk of contact with uncovered parts of the rotating saw
■
blade;
kick-back of work pieces or parts of work pieces due to
■
improper adjustment or handling;
catapulting of faulty carbide tips from the saw blade;
■
damage to the respiratory system.
■
NotE: Wear respiratory protection masks containing
filters appropriate to the materials being worked.
Ensure adequate workplace ventilation. Do not eat,
drink or smoke in the work area.
damage to hearing if effective hearing protection is not
■
worn.
warNING
Dust from certain paints, coatings and materials may
cause irritation or allergic reactions to the respiratory
system. Dust from wood such as oak, beech, MDF and
others are carcinogenic. Material containing asbestos
should only ever be worked or processed by qualified
specialist operators.
warNING
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.

KNow your produCt

See page 180 - 181.
1. Handle
2. Power switch
3. Safety lock handle
4. Upper guard
5. Saw blade
6. Lower guard
7. Main fence
8. Clamp
9. Turntable
10. Base
11. Table insert
12. Turntable lock handle
4
13. Balancing foot
14. Rubber foot
15. Laser switch
16. LED switch
17. Top handle
18. Lower guard cover
19. Bevel angle lock knob
20. Sliding fence
21. Mounting hole
22. Extension bar
23. Stand
24. Screws for adjusting the bevel angle limit stop
25. Spindle lock knob
26. Dust bag
27. Cutting depth adjustment knob
28. Bracket stop
29. Maximum cutting depth stop
30. Linear rod stop knob
31. Winding support
32. Screws for adjusting mitre angle
opEratIoN
The product features a moving saw blade that can be set at
various angles by the operator when cutting a work piece
which is securely fixed to the base of the product. It must
be operated by only one person to prevent unintentional
contact with the moving saw blade.
The principles for safe operation of the product are as
follows:
Maintain saw, blades and work area in good condition.
■
Secure the mitre saw base to either a sturdy work
■
bench or its dedicated stand. The product may move
and tip if it is not adequately secured.
Set up and lock the cutting angles and depth before
■
making the cut.
Secure the work piece to the mitre saw base. Use the
■
clamp provided and, where necessary, use additional
clamps or holding mechanisms to prevent unintentional
movement of the work piece while cutting.
Check that the operation of the blade guards are
●
not restricted by the position of the work piece.
Ensure that the fence and other parts of the product
●
will not be cut as the blade lowers to the cutting
position.
Start the motor and allow the blade to reach full speed
■
before slowly lowering it to cut the work piece. Slide
the blade assembly backwards and/or forwards to
complete the cut as necessary.
Allow the blade assembly to rise to its upper position
■
where the blade guards are fully closed. Switch off the
motor and allow the blade to come to a complete stop
before removing the work piece or off-cuts, or before
reaching into the area of the blade.
Before first use, ensure that the angle of the bevel or mitre
set on the product matches the angle to be produced on
the work piece. Check this on a discarded piece of wood
English