Residual Risks; Know Your Product - Ryobi ECO2335HG Traduction Des Instructions Originales

the path of the wheel.
Never stand on the tool. Serious injury could occur if the
tool is tipped or if the wheel is unintentionally contacted.
Never perform any operation "freehand". Always
secure the work piece to be cut in the vice. Refer to
specification table for safe minimum size of work piece.
Always ensure you grip at least 80 mm in the vice jaws
to ensure security while grinding.
Never hand hold a work piece, it will become very hot
while being cut.
A power spike causes voltage fluctuations and may
affect other electrical products in the same power
line. Connect the product to a power supply with an
fluctuations. Contact your electric power supplier for
further clarification.
It is recommended that the tool always be supplied
via a residual current device having a rated residual
current of 30mA or less.
RYOBI recommends that you use Metal cutting Disc
COSB355A1 as a replacement whenever you need a
new disc.
SAFETY WARNINGS FOR FITTING AN ABRASIVE
WHEEL
To reduce the risk of injury, user must read and
comply with instructions, warnings and operator's
manual before starting to use this abrasive wheel.
Failure to heed these warnings can result in wheel
breakage and serious personal injury. Save these
instructions.
The use of any wheel other than the one recommended
in the machine instruction manual may present a risk of
personal injury. Use only abrasive wheels which have
marked speed equal or greater to that marked on the
machine.
Never use abrasive wheel that is too thick to allow outer
flange to engage with the flats on the spindle. Larger
wheels will come in contact with the wheel guards,
while thicker wheels will prevent the bolt from securing
the wheel on the spindle. Either of these situations
could result in a serious accident and can cause
serious personal injury.
This abrasive wheel is for ferrous metal cutting only. Do
not attempt to cut wood or masonry with it. Never cut
magnesium or magnesium alloy with it.
This abrasive wheel is only suitable for dry cutting,
Do not use damaged abrasive wheels, do not use
wheels that are chipped, cracked or otherwise
defective.
Ensure that the abrasive cutting-off wheel is correctly
fitted and tightened before use.
The direction of rotation of the abrasive wheel is
indicated on the tool, make sure the direction mark on
4
wheel consistent with the direction identified on the tool
while installing and changing abrasive wheel.
can cause cracks.
Machine should never be connected to power supply
when you are installing or removing abrasive wheels.
Store your spare abrasive disc's carefully, they are
easily damaged.
Information available on the abrasive wheel label
The information on the wheel label is IMPORTANT. Read
and check it carefully to ensure you are selecting the
correct type of disc.
1. Manufacturer, supplier, importer or trade mark
2. Nominal dimensions of abrasive wheel, in particular the
diameter of the bore
3. Abrasive type, grain size, grade or hardness, type of
bond and use of reinforcement e.g.
41A24RBF80
41--- abrasive type, flat cutting-off wheel
A --- abrasive material: brown corundum
24 --- grain size
R --- grade or hardness
BF --- type of bond
4.
5.
6. For declaration of conformity, the abrasive products
shall be marked with EN 12413
7. Restriction of use and safety warning symbols.
8.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
Stability. Ensure the tool is stable, if necessary secure it.
Inhalation of dust. Wear a mask if necessary.
Sparks and hot metal particles, these can cause fire,
skin burns. Wear protective equipment during using.
Eye injury from metal particles. Wear eye protection
when working.
hearing protection.

KNOW YOUR PRODUCT

See page 172.
1. Handle, insulated gripping surface
2. Trigger switch
3. Top handle
4. Spindle lock
5. Cutting depth adjustment screw
6. Cutting depth lock nut
English