Technical Data; Declaration Of Conformity; Starting Operation; Working Advice - Bosch GSC 75-16 Professional Notice Originale

OBJ_BUCH-2740-001.book Page 10 Friday, January 22, 2016 9:39 AM
10 | English

Technical Data

Sheet Metal Shears
Article number
Rated power input
Output power
Stroke rate at no load n
0
Stroke speed under load
Max. steel sheet cutting
capacity*
Smallest curve radius
Weight according to
EPTA-Procedure 01:2014
Protection class
2
* to 400 N/mm with reference to steel sheet
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards: EN 60745-1,
EN 60745-2-8, EN 50581.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 19.01.2016
Operation

Starting Operation

 Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Switching On and Off
To start the machine, push the On/Off switch 1 forwards.
To lock the On/Off switch 1, additionally push down the front
of the switch.
To switch off the machine, release the On/Off switch 1. When
the On/Off switch is locked, press on the rear of the switch
and then release it.
To save energy, only switch the power tool on when using it.
1 609 92A 1S7 | (22.1.16)

Working Advice

 Before any work on the machine itself, pull the mains
GSC 75-16
plug.
3 601 E00 5..
Apply the power tool to the workpiece only when switched on.
W 750
W 400
-1
min 5200
-1
min 4000
mm 1.6
mm 35
kg 1.7
/II
Guide the power tool at an angle of 80 to 90° to the surface of
the sheet metal and do not tilt it to the side.
Guide the machine evenly and with light feed in the cutting di-
rection. Excessive feed significantly reduces the service life of
the saw blade and can cause damage to the power tool.
When cutting curves, make sure not to tilt the power tool lat-
erally and work with low feed rate only.
Maximum Steel Sheet Cutting Capacity
The maximum steel sheet cutting capacity d
the strength properties of the material to be cut.
The machine allows for cutting of metal sheet to the following
thicknesses:
Material
Steel
Aluminium
Adjusting Cutter Clearance a
 Before any work on the machine itself, pull the mains
plug.
a
d
max
[mm]
0.3–0.6
0.8–1.2
1.3–1.6
For softer or more ductile materials, the clearance a must be
decreased; for harder or more brittle materials, increased.
80–90°
Max. strength property
2
[N/mm ]
400
600
800
200
The cutter clearance a (gap between the
cutters) depends on the sheet thickness
d to be cut.
max
Cutter clearance a
[mm]
0.10
0.25
0.30
depends on
max
d
max
[mm]
1.6
1.2
0.7
2.2
Bosch Power Tools