Technical Data; Dust/Chip Extraction - Bosch GST Professional 80 PB Notice Originale

All manuals and user guides at all-guides.com
OBJ_BUCH-985-003.book Page 7 Tuesday, March 20, 2012 11:17 AM

Technical Data

Jigsaw
Article number
Stroke rate control
Stroke rate preselection
Orbital action
Rated power input
Output power
Stroke rate at no load n
0
Stroke
Cutting capacity, max.
– in wood
– in aluminium
– in non-alloy steel
Bevel cuts (left/right), max.
Weight according to EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Assembly
Before any work on the machine itself, pull the mains
plug.
Replacing/Inserting the Saw Blade
When mounting the saw blade, wear protective gloves.
Danger of injury when touching the saw blade.
Selecting a Saw Blade
An overview of recommended saw blades can be found at the
end of these instructions. Use only T-shank saw blades. The
saw blade should not be longer than required for the intended
cut.
Use a thin saw blade for narrow curve cuts.
Inserting/Replacing the Saw Blade (see figure A)
Before inserting the saw blade 9, set the adjusting lever for or-
bital action 6 to setting III.
Insert the screwdriver 12 from above into the stroke rod
13 and turn approx. 3–4 turns in anticlockwise direction.
Insert the saw blade 9 lateral to the cutting direction into
the stroke rod 13.
Turn the saw blade 9 so that the toothing faces toward the
cutting direction. Pull the saw blade 9 a little downward
until it engages.
While inserting the saw blade, pay attention that the back
of the saw blade is positioned in the groove of the guide
roller 8.
Insert the screwdriver 12 from above into the stroke rod
13 and turn in clockwise direction until the saw blade 9 is
locked.
Check the tight seating of the saw blade. A loose saw
blade can fall out and lead to injuries.
For removal of the saw blade, proceed in reverse order.
Bosch Power Tools
GST 80 PB
3 601 E81 2..
–
–
W 580
W 350
-1
min 3100
mm 26
mm 80
mm 20
mm 10
° 45
kg 2.4
/II
Splinter Guard (see figure B)
The splinter guard 14 (accessory) can prevent fraying of the
surface while sawing wood. The splinter guard can only be
used for certain saw blade types and only for cutting angles of
0°. When sawing with the splinter guard, the base plate 7
must not be moved back for cuts that are close to the edge.
Press the splinter guard 14 from the bottom into the base
plate 7.

Dust/Chip Extraction

Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Operation
Operating Modes
Before any work on the machine itself, pull the mains
plug.
Orbital Action Settings
The four orbital action settings allow for optimal adaptation of
cutting speed, cutting capacity and cutting pattern to the ma-
terial being sawed.
English | 7
GST 80 PBE
3 601 E81 5..
580
350
500–3100
26
80
20
10
45
2.4
/II
1 609 929 S81 | (20.3.12)