EINHELL ROYAL MKS 38/40 Mode D'emploi page 19

Anleitung MKS 38-40 SPK 1
OPERATING INSTRUCTIONS
• ENGINE PRE-START CHECKS
WARNING: Never start or operate the saw
unless the bar and chain are properly
installed.
1. Fill the fuel tank (A) with correct fuel mixture
(Fig. 8).
2. Fill the oil tank (B) with correct chain and bar oil
(Fig. 8).
3. Be certain the chain brake is disengaged (C) before
starting unit (Fig. 8).
• TO START ENGINE
The choke has 3 positions: RUN (A), HALF (B) and
CHOKE (C) (Fig. 9A).
1. Slide red STOP switch (D) up for starting (Fig. 9B).
2. Move the yellow choke lever (E) to (CHOKE)
(Fig. 9C).
3. Push the primer bulb (F) 10 times (Fig. 9D).
A
Fig. 8 Fig. 9A
B
C
D
E
Fig. 9B
Fig. 9C Fig. 9D
4. Latch throttle advance: depress latch and hold (A)
squeeze throttle trigger (B) release trigger and then
the latch (Fig. 10A).
5. Place saw on a firm, flat surface. Hold saw firmly as
shown. Pull starter rapidly 4 times. Beware of
moving chain! (Fig.10B)
6. Move yellow choke lever (D) to (HALF)
(Fig.10C).
7. Hold saw firmly and pull starter rapidly 4 times.
Engine should start (Fig. 10D).
8. Warm up for 10 seconds. Depress and release
trigger (E) for IDLE, then go to step 9 (Fig. 10E).
9. Move yellow choke lever (F) to (RUN) (Fig. 10F).
If engine failed to start, repeat these instructions.
A
Fig. 10A B Fig. 10B
Fig. 10C
10.05.2004 15:05 Uhr
E
Fig. 10D Fig. 10E
Fig. 10F
• RE-STARTING A WARM ENGINE
1. Make sure the switch is in the ON position.
2. Move the choke lever to (HALF).
3. Depress the primer bulb 10 times.
4. Set the throttle latch.
5. Pull the starter rope rapidly 4 times. The engine
should start.
6. Move the choke lever to (RUN).
7. Release the throttle latch.
• TO STOP ENGINE
1. Release trigger and allow engine to return to idle
speed.
2. Move STOP switch down to stop engine.
NOTE: For emergency stopping, simply activate chain
A
brake and move STOP switch down.
• CHAIN BRAKE OPERATIONAL TEST
B
Test the chain brake periodically to ensure proper
tion.
C
Perform a chain brake test prior to initial cutting,
following extensive cutting, and definitely following any
Chain brake service.
F
TEST CHAIN BRAKE AS FOLLOWS (Fig. 11) :
1. Place saw on a clear, firm, flat surface.
2. Start engine.
3. Grasp the rear handle (A) with your right hand.
4. With your left hand, hold the front handle (B) [not
chain brake lever (C)] firmly.
5. Squeeze the throttle trigger to 1/3 throttle, then
immediately activate the chain brake lever (C).
WARNING:
Activate the chain brake slowly
and deliberately. Keep the chain from touching
anything; don t let the saw tip forward.
6. Chain should stop abruptly. When it does,
immediately release the throttle trigger.
WARNING: If chain does not stop, turn
engine off and take your unit to the nearest
Talon Authorized Service Center for service.
7. If chain brake functions properly, turn the engine off
and return the chain brake to the DISENGAGED
position.
D
B
A
C
Fig. 11
Seite 19
GB
F
func-
19