Scheppach 39048029914 Traduction Des Instructions D'origine page 36

Turn it so that the plates of the spool cover are pushed
with the springs in the line spool housing.
7. Now, press the spool cover together with the line
spool, until it engages in the line spool housing.
8. The knife (A) in the protective hood (18) shortens the trim-
ming line to the correct length, when the engine starts again.
Grinding the safety hood blade
The safety hood blade can become blunt over time.
• When you notice this, undo the screw holding the
safety hood blade on the safety hood.
• Clamp the blade in a vise.
• Sharpen the blade with a flat file and make sure that
the angle of the cutting edge is not altered in the pro-
cess. File in one direction only.
Replacing and resharpening the cutting blade at the end
of the mowing season always resharpen the cutting blade
or, if required, replace the cutting blade with a new one.
Grinding cutter blade
If the blade is only slightly dull, they can re-sharpen
themselves.
• Clamp the blade in a vise.
• Sharpen the blade with a flat file and make sure that
the angle of the cutting edge is not altered in the pro-
cess. (~25°) File in one direction only.
• Replace the blade at the latest after five times
scharpening.
Replace the blade with heavy wear or broken blade.
Unbalanced blades will cause the brush cutter to vibrate
violently-risk of accident!
Change and clean the spark plug Fig. 30-31
Check the spark plug air gap at least once a year or
when the engine starts poorly. The correct gap between
ignition flag and ignition contact is 0.25"/0.63 mm.
• Wait until the engine has cooled down completely.
• Pull the spark plug cap off the spark plug, and use the
supplied spark plug wrench to remove the spark plug
by turning.
• When the electrode is severely worn out or reveals a
strong incrustation, the spark plug must be replaced
with an equivalent plug.
• A strong incrustation of the spark plug can be caused
by: Amount of oil is too high in the gasoline mix, poor
oil quality, old gasoline mix, or plugged up air filter.
• Screw the spark plug by hand completely into the
thread. (Avoid jamming it)
• Use the supplied spark plug wrench to tighten the
spark plug.
• When using a torque wrench, the tightening torque is
12-15 Nm.
• Plug the spark plug socket correctly on the plug.
Clean the air filter Fig. 32-35
Soiled air filters reduce the engine power by supplying
too little air to the carburetor. Dust and pollen plug up
the pores of the filter made of foamed plastic. Regular
checks are therefore essential.
• Unclip the air filter cover and remove the sponge filter
element.
36 GB
• To avoid objects falling into the air tank, replace the air
filter cover.
• Wash the filter element in warm soap water, rinse and
allow drying naturally.
Important: Never clean the air filter with petrol or in-
flammable solvents.
In order not to shorten the service life of the engine, a
damaged air filter must be replaced at once.
m Warning!
Never run the engine without the air filter element in-
stalled.
Care of the guide rail
Turn the rail around every time you have the chain
sharpened or replaced. This will avoid a one-sided wear
of the rail, especially at the top and bottom.
Regularly clean
1 = the opening for the oil supply
2 = the oil passage
3 = the raceway groove of the rai
Servicing and sharpening of saw chain
The correct sharpened chain
Working effectively with the chainsaw is only possible if
the chain is in good condition and
sharp. This also reduces the risk of kickback. The chain
can be re-sharpened by any dealer. Do not attempt to
sharpen the chain yourself unless you have the neces-
sary special tools and experience. A properly sharpened
chain goes way through the wood and it requires very lit-
tle pressure. Do not work with a dull or damaged chain. It
increases physical exertion, increase the vibrations and
leads to unsatisfactory results and higher wear.
• Clean the chain.
• Check it.
• Replace damaged or worn parts with matching spare
parts they are in the shape and size of the original
parts as necessary.
• Sharpening a chain should be performed only by ex-
perienced users!
Notice. Below the angle and dimensions If the chain is
not properly sharpened or the depth is too small, there
is a higher risk of reversion effects and resulting inju-
ries! The chain cannot be fixed on the guide rail. It is
therefore best to remove the chain from the rail and
then sharpen.
• Select the appropriate tools for the chain pitch sharp-
ening tool. See "Specifications" for the allowed chain
pitches.
The chain pitch (for example 3/8 ") is highlighted in the
depth of each blade.
2
1
3