Battery Charging; Removing The Battery; Battery Charge Indicator - Bosch GCM 18V-305 GDC Professional Notice Originale

Remove the cover for the Bluetooth® Low Energy Mod-
u
ule GCY 42 on the power tool, e.g. using a screwdriver
or a large coin. Using unsuitable objects can damage the
electronics or the cover.

Battery Charging

Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.

Removing the Battery

The battery (31) is equipped with two locking levels to pre-
vent the battery from falling out if the battery release but-
ton (32) is pressed unintentionally. The battery is held in
place by a spring when fitted in the power tool.
To remove the battery , press the release button and pull the
battery out of the power tool. Do not use force to do this.

Battery charge indicator

The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Note: The state of charge of the battery is also displayed on
the user interface (3).
Battery model GBA 18V...
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Bosch Power Tools
Battery model ProCORE18V...
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Fitting individual components
– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packing material from the power tool and the
accessories provided.
Fitting the locking knob (see figure a)
– Screw the locking knob (12) into the corresponding hole
above the lever (13).
Always tighten the locking knob (12) firmly before
u
sawing. Otherwise the saw blade can become wedged in
the workpiece.
Stationary or flexible mounting
To ensure safe handling, the power tool must be
u
mounted on a flat, stable work surface (e.g. work
bench) before use.
Mounting on a work surface (see figure b1)
– Use suitable screw fasteners to secure the power tool to
the work surface. The holes (9) are used for this purpose.
or
– Firmly clamp the base of the power tool to the work sur-
to
face with commercially available screw clamps.
Mounting on a Bosch saw stand
(see figure b2)
(GTA 2500 W, GTA 2500 Compact, GTA 2600, GTA
3800)
With the height-adjustable legs, Bosch GTA saw stands
provide firm support for the power tool on any surface. The
workpiece supports of the saw stand are used for underlay-
ing long workpieces.
Read all the warnings and instructions included with
u
the saw stand. Failure to observe the warnings and fol-
low instructions may result in electric shock, fire and/or
Capacity
serious injury.
60−100 %
Assemble the saw stand properly before mounting the
u
power tool. Correct assembly is important to prevent the
30−60 %
risk of collapsing.
5−30 %
– Mount the power tool on the saw stand in the transport
0−5 %
position.
English | 39
Capacity
80−100 %
60−80 %
40−60 %
20−40 %
5−20 %
0−5 %
1 609 92A 5HG | (08.04.2020)