Carrying Out Internal Cuts - EINHELL BT-SS 405 E Mode D'emploi D'origine

Anleitung_BT_SS_405_SPK1:_
5.3 Assembly
Caution! Pull out the power plug before carrying out
any maintenance and conversion work on your
fretsaw.
5.3.1 Mounting the saw blade guard and the
sawdust blower facility (Fig. 4/5/6)
Put the retention bolt (9) on the radial arm (19).
Slide the saw blade guard (10) onto the retention
bolt (9).
Insert the screw (20) through the bore hole of the
retention bolt (9) and the saw blade guard (10).
Use the nut (21) to secure the screw from falling
out.
The saw blade guard can be fixed at various
heights with the clamping screw (11).
Mount the blow-off device (16) as shown in Fig. 6.
5.3.2 Changing the blade (Fig. 1/3/7)
Turn the clamping screw (14) clockwise in order
to take the tension off the blade (15).
Unscrew the left cover (4).
First take the blade out of the top blade holder
(13), pressing down the upper pendulum arm as
you do so.
Then take the blade out of the bottom blade
holder (8).
Pull the blade up and out through the table insert
(18).
Install the new blade in reverse order.
Caution: Always insert the blade so that the teeth
point toward the saw table.
The blade can be inserted in slot a or b;
Slot a: For cuts along the axis of the radial arm.
Slot b: For cuts across the axis of the radial arm.
Tension the blade by turning the clamping screw
(14) anticlockwise (right-hand thread).
5.3.3 Tilting the saw table (Fig. 8)
Undo the locking screw (5).
Tilt the table (7) to the left until the indicator (17)
points to the required angle value on the scale
(6).
Important: For precision work you should first
carry out a trial cut and then re-adjust the tilt
angle as required.
06.12.2010 7:27 Uhr Seite 11
6. Operation
6.1 Please note:
Your saw does not cut wood automatically. For
cutting to occur, you have to guide the wood
against the blade.
The teeth cut only on the down stroke of the
blade.
You have to guide the wood slowly against the
blade because the teeth are very small.
Every new user needs a certain training period.
You are certain to break a number of blades at
the beginning.
When cutting thick timber, be particularly careful
not to bend or twist the blade. This will help to
prolong blade life.
6.2 On/Off switch (Fig. 3 / Item 2)
Press the green button to switch the saw on.
Press the red button to switch the machine off.
Please note: The machine is equipped with a safety
switch to prevent it being switched on again
accidentally after a power failure.
6.3 Blade speed regulator (3)
The blade speed regulator allows you to set the
blade speed appropriate to the material to be cut.

6.4 Carrying out internal cuts

1. A feature of this fretsaw is that it allows you to
carry out internal cuts in a panel without
damaging it on the outside or circumference.
WARNING: TO PREVENT INJURIES DUE TO THE
SAW STARTING UP ACCIDENTALLY, ALWAYS
SET THE SWITCH TO „0" POSITION AND PULL
THE POWER PLUG OUT OF THE SOCKET-
OUTLET BEFORE YOU REMOVE OR CHANGE
THE BLADE.
2. To carry out internal cuts in a panel: Remove the
blade as described in Section 5.3.2
3. Drill a hole in the panel in question.
4. Place the panel on the saw table with the drilled
hole above the access hole.
5. Install the blade through the hole in the panel and
adjust the blade tension.
6. When you have completed the internal cuts,
remove the blade from the blade holders (as
described in Section 5.3.2) and take the panel off
the table.
GB
11