Safety Instructions; Technical Data - Eaton CROUSE-HINDS Série Mode D'emploi

1.

Safety instructions:

Target group:
For skilled electricians and
suitable qualified, instructed
personnel in accordance with national
legislation, including the relevant
standards and, where applicable, in acc.
with IEC/EN 60079-14 on electrical
apparatus for explosive atmospheres.
– The light fitting is not suitable for use in
hazardous areas of zone 0, 1 and
zone 20, 21!
– The requirements of the IEC/EN 60079-31
regarding excessive dust deposits and
temperature to be considered from the
user.
– The technical data indicated on the light
fitting are to be observed!
– Disconnect equipment before opening!
– Changes of the design and modifications
to the light fitting are not permitted!
– The light fitting shall be operated as
intended and in undamaged and perfect
condition!
– Repairs may only be carried out by CCH/
CEAG or a qualified "electrician"!
– Do not keep these operating instructions
inside the light fitting during operation!
Observe the national safety rules and
regulations for prevention of accidents
and the following safety instructions
which are marked with an (
operating instructions!
Explosion protected light fittings
Series: nLL* 15 LED 600/1200/1200HT/1500
2.

Technical data

ATEX EU - Declaration of conformity
ATEX Marking accd. 2014/34/EU and standard:
Gas
with optional switch
V-CGS
V-CGS with optional switch
Dust
Rated voltage
Rated frequenzy
Lamps to be fitted with LED tubes (Sockel G5)
Type
nLL* 15 LED 600
nLL* 15 LED 1200 / 1200HT
nLL* 15 LED 1500
Max. quantity of nllk / MCB
nLL* 15 LED 600/1200/1200HT/1500:
Protection acc. to IEC/EN 60529
Insulation class to IEC/EN 61140
max. permissible ambient temperature
nLL* 15 LED 600
nLL* 15 LED 1200 / 1500
nLL* 15 LED 1200HT
nLL* 15 LED ... V-CGS
Storage temperature in original packing
Limits for versions with DALI interface
) in these
Currents
Temperature fuse driver
Supply terminal clamping capacity
2x per screw-terminal
min.
max.
Conductor cross-section with through-wiring
Cable entries moulded plastics
suitable cables and test torques of the
pressure screw
Seal 1+2+3
Seal 1+2
Seal 1
Test torque for screw in thread cable entry
Metal thread
For permanently laid cables only
Dimensions of light fittings and for mounting
Weight
nLL* 15 LED 600
nLL* 15 LED 1200
nLL* 15 LED 1500
(1)
Intensive sun radiation in areas of high ambient temperatures may cause inadmissible temperature rise inside
of the luminaire. This may result a decrease in lifetime. Therefore those luminaires should be switched off
during daytime by a photocell control.
(2)
The tests of clamping ranges and torque values were performed with metal mandrel. The clamping range can
vary by using cables with different manufacturing tolerances and material properties. Please use a suitable
combination of seals in the intermediate area, so that the cap nut can be tightened in future maintenance work
on the cable entry.
(1)
Temperature „A"
Temperature „B"
min.
1 2
3
(2)
max.
min.
1 2
3
(2)
max.
min.
1 2
3
(2)
max.
CCH 15 ATEX 1044
II 3 G Ex ec IIC T4 Gc
II 3 G Ex ec db IIC T4 Gc
II 3 G Ex ec mb ib IIC T4 Gc
II 3 G Ex ec db mb ib IIC T4 Gc
II 3 D Ex tc IIIC T80°C Dc
220 V - 240 V AC/DC
50 - 60 Hz
Aura UltiLED Long Life
8 W
Aura UltiLED Long Life / Aura UltiLED pro Long Life
17 W 28 W
23 W 34 W
B10 C10 B16
8 13 12
IP 66
I
-25 °C ... +50 °C / +55 °C
-25 °C ... +45 °C
-25 °C ... +55 °C
-25 °C ... +50 °C
-25 °C ... +40 °C
nLL* 15 LED 600 nLL* 15 LED
1200/1200HT/1500
max. 350 mA max. 700 mA
90 °C 90 °C
95 °C 95 °C
single-wire multi-wire
1.5 mm 1.5 mm
2
6.0 mm 6.0 mm
2
2.5 mm for max. 16 A
2
M25 x 1,5
Ø cable (mm) Pressure screw (Nm)
8.0 1.5
10.0 2.0
10.0 2.3
13.0 2.6
13.5 1.3
17 .5 2.3
3.0 Nm
M20 x 1.5
see fig. 2
approx. 4.0 kg
approx. 6.0 kg
approx. 7 .0 kg
GB
C16
21
2
2
7