Master/Slave Mode; Dmx Control; Connection; Setting The Number Of Dmx Channels - IMG STAGELINE WASH-50LED Mode D'emploi

Repeat steps 3 and 4 for the other parameters .
This menu item will not be exited automatically;
it will remain active until the button MENU is
pressed or the unit is disconnected from the
power supply .

7.3 Master/slave mode

Multiple units WASH-50LED can be operated
in sync . In this mode, a unit (master unit) will
control the other units (slave units) . Connect
the units in a chain . Please refer to chapter 8 .1,
skipping step 1 . To set the units to the mode
desired:
1) Call up the menu with the button MENU .
2) Call up the menu item
 or  and then press ENTER to confirm .
The display will indicate the current setting .
3) Use the button  or  to set the operating
mode desired and then press ENTER to save
it .
master unit
slave unit
slave unit (with movements in oppo-
site directions)
As an alternative, use the button SLAVE on the
IR remote control to switch between master
mode and slave mode .
At the master unit, call up an automatic (mu-
sic-controlled) program or make a manual set-
ting . will appear on the display of the slave
units .

8 DMX Control

DMX stands for Digital Multiplex and allows
for digital control of multiple DMX units via
a common control cable . For operation via a
DMX light controller (e . g . DMX-1440 or DMX-
510USB from "img Stage Line"), the WASH-
50LED is equipped with 16 DMX control chan-
nels . However, the spotlight may be switched to
9 DMX channels or to a single DMX channel if
not all control options are required or if less than
16 channels are available at the controller . The
functions of the channels and the corresponding
DMX values can be found in chapter 11 .1 .
18

8.1 Connection

As a DMX interface, the unit offers 3-pole XLR
connectors with the following pin configura-
tions:
Pin 1 = ground, 2 = DMX−, 3 = DMX+
For connection, special cables for DMX signal
transmission are recommended (e . g . cables of
the CDMXN series from "img Stage Line") . For
cable lengths exceeding 150 m or when con-
trolling more than 32 units via a single DMX
output, it is generally recommended to insert a
DMX level matching amplifier (e . g . SR-103DMX
from "img Stage Line") .
1) Connect the control input DMX IN (4) to the
with the button
2) Connect the control output DMX OUT (5) to
3) To prevent interference in signal transmission,
8.2 Setting the number of
To operate the spotlight by means of a light
controller, set the DMX start address (
ter 8 .3) and the number of DMX channels . The
number of DMX channels depends on the func-
tions required and, if applicable, also on the
number of the control channels available at the
light controller . Please refer to chapter 11 .1 for
the functions available with the different chan-
nel modes (1, 9, 16 channels) and then select
the appropriate number of DMX channels:
1) Call up the menu with the button MENU .
2) Select the menu item
DMX output of the light controller or of a
different DMX-controlled unit .
the control input of the second DMX-con-
trolled unit . Proceed in the same way to con-
nect the output of the second unit to the
input of the third unit etc . until all DMX-con-
trolled units have been connected in a chain .
in case of long cables or a multitude of units
connected in series, terminate the control
output of the last DMX unit in the chain with
a 120 Ω resistor (> 0 .3 W): Connect a cor-
responding terminating plug (e . g . DLT-123
from "img Stage Line") to the output jack .
DMX channels
 or  and then press ENTER to confirm .
The display will indicate the current setting .
☞
chap-
with the button