Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
WARNING Install the spotlight safely and
expertly. When installing it at a place
where people may walk or sit under
it, additionally secure it (e. g. via a
safety rope on the mounting bracket;
fasten the safety rope in such a way
that the maximum falling distance of
the unit will not exceed 20 cm).
1. Install the spotlight via its mounting brackets (2),
e. g. with a stable mounting screw or a support
for lighting units (C hook) to a cross bar.
To align the spotlight, release the two locking
screws (1) of the mounting brackets. Adjust the
desired inclination of the spotlight and fasten
the screws.
2. Alternatively, set up the spotlight on its own:
Fold out the mounting brackets underneath the
spotlight and use them as a stand. Then fasten
the locking screws.
4.2 Barn doors
To reduce the light beam angle, the barn doors
PARC-64B (optional) are available: Insert the barn
doors into the outer slot at the front of the spotlight
and secure them with the clip (5). To additionally
secure the door barns, screw the 4 screws supplied
into the threaded holes of the door barns.
4.3 Switching on
WARNING To prevent damage to your eyes,
never look directly into the light
source.
Please note that fast changes in light-
ing may trigger epileptic seizures with
photosensitive persons or persons
with epilepsy!
Connect the plug of the mains cable (8) to a
mains socket (230 V~ / 50 Hz). Thus, the spotlight is
switched on, its display (3) will indicate the menu
item most recently selected and go out after
30 seconds. As soon as you press one of the con-
trol buttons (7), the display will light up again for
30 seconds.
5 Operation
To select the operating mode and the different func-
tions, use the menu via the control buttons MENU,
ENTER, UP and DOWN (7). Figure 2 on page 2
shows the selection of the modes and functions via
the menu and the indications on the display (3).
5.1 Independent operation
For independent operation, use the control buttons
(7) to set the value for cool white and warm white,
to switch on the stroboscope function and to set the
flash rate.
1) Press the button MENU repeatedly until
appears on the display.
2) Press the button ENTER. ,
ber will appear on the display.
= brightness cool white
= brightness warm white (0 – 255)
= flash rate (0 – 20 Hz) of the stroboscope
3) Use the button ENTER to select the three set-
ting functions one after the other and then use
the button UP or DOWN to set the brightness or
flash rate.
The colour temperature of the light beam is
defined by the brightness ratio between cool
white and warm white.
Important: Do not exit the menu item for the bright-
ness or the flash rate with the button MENU before
switching off the spotlight. If you do, the spotlight
will remain dark when you switch it on again.
5.2 Synchronous control of multiple
spotlights (master / slave mode)
Multiple spotlights PARC-64 / CTW may be com-
bined. The brightness and flash rate settings made
at the master unit will be automatically transferred
to the slave units.
1) Connect the spotlights with each other in a
chain, using the DMX connections; please refer
to chapter 5.3.1, "DMX connection", skipping
step 1.
2) Set the master unit to the master mode and all
slave units to the slave mode:
a) Press the button MENU repeatedly until
appears on the display.
b) Press the button ENTER and then use the
button UP or DOWN to select:
= master mode for the master unit
= slave mode for the slave units
3) At the master unit, set the brightness and flash
rate desired.
5.3 Operation with a DMX controller
For operation via a DMX light controller (e. g. DMX-
1440 or DMX-510USB from "img Stage Line"), the
spotlight is equipped with four DMX control chan-
nels. DMX is short for digital multiplex and means
digital control of several DMX units via a common
control cable. The functions of the channels and
the DMX values can be found in chapter 5.3.3.
or
and a num-
(0 – 255)
GB
9
Publicité
Table des Matières
