Warranty Claims - Exclusion Of Liability; Certificates - Guidelines; Shipping; Receipt - Helios ALB-220/4/50/30 WW/EH Notice De Montage Et D'utilisation

Installation and Operating Instructions
EN
CHAPTER 2
GENERAL INFORMATION
m
ATTENTION
m
ATTENTION
CHAPTER 3

TECHNICAL DATA

* (performance and noise data from the
currently applicable Helios documentation
and the internet)
Fresh Air Boxes
2 .0 Warranty claims – Exclusion of liability
All versions of this documentation must be observed, otherwise the warranty shall cease to apply. The same applies
to liability claims against Helios. The use of accessory parts, which are not recommended or offered by Helios, is not
permitted. Any possible damages are not covered by the warranty. Changes and modifications to the unit are not
permitted and lead to a loss of conformity, and any warranty and liability shall be excluded in this case.
2 .1

Certificates - Guidelines

If the product is installed correctly and used to its intended purpose, it conforms to all applicable provisions and EU
guidelines at its date of manufacture.
2 .2

Shipping

The ALB is packed ex works in such a way that it is protected against normal transport strain. Carry out the shipping
carefully. It is recommended to leave the fan in the original packaging. The ALB must be kept in the housing or lugs
provided (if applicable) for transportation or installation. Only use appropriate lifting equipment and fastening devices.
Weight specifications according to the delivery note or information on the unit.
Do not transport fan on the connection cables, terminal box or impeller!
Do not stand under suspended loads!
2 .3

Receipt

The shipment must be checked for damage and correctness immediately upon delivery. If there is any damage,
promptly report the damage with the assistance of the transport company. If complaints are not made within the agreed
period, any claims could be lost.
2 .4

Storage

When storing for a prolonged time, the following steps are to be taken to avoid damaging influences: Motor protection
by dry, airtight and dust-proof packaging (plastic bag with desiccant and humidity indicators). Vibration-free, water-tight
and constant-temperature storage at a temperature in the range -20 °C to +40 °C, which must not be exceeded.
In case of storage below 0 °C, the unit must be left in standby mode under operating conditions for at least 2
hours before commissioning, so that the internal temperature can equalise .
In case of a storage period of more than three months or motor standstill, maintenance must be carried out before
commissioning. In case of reshipment (above all, over longer distances; e.g. by sea), it must be checked whether the
packaging is suitable for the form and route of transport. Damages due to improper transportation, storage or putting
into operation are not liable for warranty.
2 .5

Performance data

The fan or motor type plate gives an indication of the mandatory electrical values; which must be coordinated with the
local supply network. The fan performances* were established on a test stand according to DIN EN ISO 5801: 2010-
12; they apply to the nominal speed and standard design using an inlet nozzle, without a protection guard with unhin-
dered inflow and outflow and a pressure-side pipe section with 2.5x diameter length. Different versions and unfavour-
able installation and operating conditions can lead to a reduction of output.
2 .6

Noise data

The noise data* also refers to the aforementioned directive. Casing variations, unfavourable operating conditions and
many other things can lead to an increase in the specified catalogue values. Data that refers to certain distances (1, 2,
4 m) apply to free field conditions. With regard to installation, the sound pressure level can differ significantly from the
catalogue data, as it is highly dependent on the installation conditions, i.e. on the absorption capability of the room, the
room size among other factors.
3 .0 Technical data
Voltage, frequency
Rated current max. [A]
Protection class
Speed max. [1/min]
Output free-blowing [m³/h]
Ambient temperature min/max [°C]
Temperature class
Weight approx. kg
ALB 220/4/50/30 WW
230 V, 50 Hz, 1~
6.1
IP 20
1460
3200
+ 5/+ 35
155
80
4
ALB 280/4/60/35 WW
400 V, 50 Hz, 3 ~
2.75
IP 20
1450
4700
+ 5/+ 35
155
110