Publicité
Les langues disponibles
Les langues disponibles
Adjusting the throttle cable: Illustration A1-3*
If you experience slack in throttle cable, this can be
solved simply by tighten or loosen the bolt on the
engine block.
* Not all models have throttle cable.
Operation
Always check and refill oil before the start!
Read and apply the instructions given in the
enclosed start guide!
The oil level should always be between min. and max
on the dipstick. Fill with SAE-30 oil. There should be
total 0.45 liter oil in the engine. Use only unleaded E5
fuel to the engine. Never overfill the tank.
Cutting height adjustment: Illustration F1
(the illustrations may vary from your actual model)
The mower has 7 different heights. The cutting height
ranges from 30 mm to 75 mm
Start: Never start the mower directly on long grass.
Recoil with primer: Illustration F2
1.
Push the primer several times, first time push 3
times, if necessary, supplement with up to 3-5
times.
Note: It is not possible to drown engine
2.
Hold the handlebar for the engine brake; this will
release the engine brake.
3.
Pull the recoil starter gently until you feel resistance
in the rope, then pull quickly and energetic. Do not
at any time let go of the recoil starter but slide it
gently into starting position.
4.
Hold the bar for self-propelled in order to start
mowing
Recoil with throttle lever: Illustration F3-A
By cold engine set the choke lever on "Choke".
1.
By warm engine set the choke lever on "Run".
2.
Hold the handlebar for the engine brake; this will
release the engine brake.
3.
Pull the recoil starter gently until you feel resistance
in the rope, then pull quickly and energetic. Do not
at any time let go of the recoil starter but slide it
gently into starting position.
4.
Adjust the throttle lever if necessary
(only cold engine).
5.
Hold the bar for self-propelled in order to start
mowing.
Note: As long as operating the mower, the bar
forengine brake must be engaged.
Throttle lever*
Engine speed can be adjusted while driving. Turn gas
handle to adjust rpm. It is recommended to run at full
throttle for best cutting results.
* Note: Not all models have throttle control
Stop: Illustration F4
1.
Release the engine brake and self-propelled bar to
turn off the mower and the engine
Note: The blades will still rotate at up to 3 seconds
after stopping.
Water nozzle
The left side of the mower deck is fitted with a water
nozzle for washing the deck. (See Illustration ID-F)
•
When using the water nozzle, the machine must be
in the lowest height position and placed on the
lawn. This ensures that the water remains under
the deck during cleaning.
•
Attach a hose to the nozzle.
•
Turn on the water and start the engine.
•
The rotations of the blades will ensure that the
water will clean the underside of the deck.
If above instruction is not followed, water may
splash back on the gearbox and clutch cable,
which increases the risk of corrosion and damage
to both parts. This will not be covered by the
warranty!
Note: For best result clean the deck with the water
nozzle function right after each mowing. If the grass
dries out, this function will not work optimally.
* Note: Not all models have water nozzle
Oil change
Oil should be changed for the first time after 5 hours,
then at least 1 time per year.
You will need an oil extractor kit. Art. no. 40-11336
Oil and oil extractor kit is not included
Use an extractor kit and do as follows:
1.
Turn on the engine and let it run for 5 min or until
the engine is hot. A hot engine liquefies the oil
which makes it easier to drain.
2.
Suck the oil up through the oil filler hole using the
syringe that came with the oil extractor kit. Use the
hose to reach the sump.
3.
Transfer the used oil into a empty container.
4.
Fill the engine with SAE-30 oil.
5.
Check the oil level using the dipstick. (Min / Max)
Remember to dispose the used oil so that it does
no harm to nature. Use your local recycling station.
Air Filter
The air filter should be inspected and cleaned regularly.
If the filter has not been cleaned for a long time, the
engine's power will drop.
See Illustration A2
1.
Clean around the air filter before removing the cap.
2.
Push the flap down and gently pull the cover
3.
Wash the black foam elements in warm water and
soap.
4.
Press the water out of the foam element and let it
dry. Put a few drops of SAE-30 oil on the filter to
moisten it lightly. Carefully squeeze any surplus oil
out of the foam element and reattach.
5.
Please note that all parts are assembled correctly
and properly closed, as shown in the picture.
8
Publicité
