Publicité
Les langues disponibles
Les langues disponibles
Miscellaneous
The motor is not pre-filled with oil.
Always before start check the engine oil level.
Factory-fitted control devices, such as the handle-
mounted clutch cable, must not be removed or
exposed.
Only drain the fuel tank outdoors. Gasoline is
extremely flammable and the fumes are explosive.
Ensure that the machine is properly secured when
transported on a flatbed etc.
The lawnmower is manufactured according to the latest
safety requirements. These include a blade brake that
stops the motor and blade in 3 seconds when the blade
brake. Every precaution is only effective when it is
followed exactly. Use the following description when
you mount your lawnmower.
Identification of the parts
See Illustration ID
Notice: the illustrations may vary from your present
model
A.
Handlebar for drive *
B.
Handlebar for engine brake
C. Recoil starter
D. Wing nut
F.
Water nozzle *
G. Grass collector
H. Gasoline filling cap
I.
Air Filter
J.
Exhaust
K.
Spark plug
L.
Oil cap
M. Mulching plug
P.
Height adjustment *
Q. Side discharge guard*
R. Primer *
S.
Panel *
* may vary from your actual model.
Mounting
Unpacking: Illustration M1
Remove the mower from the box by pulling the machine
out from the side. The box contains:
1 pcs mower
2 pcs wing nut set consisting of wing nuts, bolts
and washers. (See ID; D)
Warning: Ensure that cables are not pinched.
Handlebar: Illustration M2
1.
Attach the lower handlebar tube
2.
Attach the upper handlebar on the lower. Fasten
with wing nut from the inside of the handlebar.
3.
Customize cable and secure with cable clamps
Mounting the engine brake cable: Illustration M3
1.
Gently push the top handlebar ID:B forward
2.
Insert the engine brake cable from the inside, into
the hole in the bracket on handlebar ID:B and lock.
Mounting the drive cable: Illustration M3
1.
Gently push the lower handlebar ID:A downward
2.
Insert the drive cable from the inside, into the hole
in the bracket on handlebar ID:A and lock.
Mounting the recoil-starter: Illustration M4
1.
Pull the engine brake handlebar and hold, in order
to release the starter cord on the engine.
2.
Pull gently the starter cord from the engine
(Engine brake handlebar MUST be hold)
3.
Attach the starter grip on the rack of handlebar.
4.
Release the engine brake handlebar and the
starter grip.
Mounting the panel: illustration M5*
1.
For models with panel with cup holder follow
illustration M5-1
2.
For models with panel follow illustration M5-2
*Note: Not all models do have panel
Mounting the grass collector: Illustration M6
1.
Click the frame to the grass collector.
The grass collector comes with a handy indicator
showing whether the box is full of grass and needs
emptying.
Mulching plug: Illustration M7-1
1.
Insert the mulching plug and remove side
discharge guard, if you want to mow with mulching
functionality.
NB Don't use the grass collector
Important: Remember to remove the mulching plug,
when using the grass collector.
Side discharge guard: Illustration M7-2*
1.
Lift the side guard and insert side discharge guard.
Then insert the mulching plug in rear discharger to
mow with side discharge function. NB Don't use the
grass collector
* Note: Not all models do have side discharge guard
Cable Adjustment
Before the machine is being used, the cable adjustment
should always be checked.
The cables can be checked by activating the handles
fully and check if the cable is tight. If not, it must be
tightened. If the handle cannot easily be fully activated,
the cable should be loosened.
After first season, it must be expected that the cables
need to be adjusted for optimal activation, as cables
can stretch when used.
The following cables may be necessary to readjust:
Illustration A1
1.
Cable for drive
2.
Cable for engine brake
3.
Cable for throttle cable
Note: The choke cable cannot be adjusted!
Adjusting the drive cable: Illustration A1-1*
If you experience slack in the drive cable, this can be
solved simply by tighten or loosen the bolt on the cable.
1.
Tighten turning clockwise - loosen the cable.
2.
Tighten turning anti clockwise - tighten the cable.
* Cable can only be adjusted on some models.
Adjusting the engine brake cable: Illustration A1-2
If you experience slack in engine brake cable, this can
be solved simply by tighten or loosen the bolt on the
engine block.
7
Publicité
