Technical Data; Initial Operation - Bosch PowerPack 300 Notice Originale

OBJ_BUCH-1407-003.book Page 2 Friday, October 12, 2012 1:01 PM

Technical Data

Drive Unit
Article number
Power output
Output torque, max.
Rated voltage
Operating temperature
Storage temperature
Degree of protection
Weight, approx.
Drive HMI
Article number
Max. charging current, USB
connection.
Charging voltage, USB con-
nection
Operating temperature
Storage temperature
Degree of protection
Weight, approx.
Lighting*
Rated voltage
Power output
– Front light
– Rear light
* Not possible via the eBike battery pack in all country-specific versions,
depending on the statutory regulations
Assembly
Inserting and Removing the Battery Pack
For inserting and removing the battery pack in/from the
eBike, please read and observe the battery pack operating in-
structions.
Inserting and Removing the Drive HMI
(see figure A)
To insert the drive HMI 3, slide it from the front into the
holder 4.
To remove the drive HMI 3, press the lock latch 15 and slide
the drive HMI toward the front out of the holder 4.
 Remove the drive HMI when parking the eBike, so that
the drive cannot be used by unauthorised persons.
Without the drive HMI, the eBike system cannot be
switched on.
Bosch eBike Systems
The drive HMI can also be secured in the holder against re-
moving. For this, remove the holder 4 from the handlebar. In-
Drive Unit Cruise
sert the drive HMI into the holder. Screw the locking screw 16
0 275 007 006/
from below into the corresponding thread in the holder.
0 275 007 007 Mount the holder onto the handlebar again.
W 250
Checking the Speed Sensor (see figure B)
Nm 50
The speed sensor 17 and its spoke magnet 18 must be
V 36
mounted in such a manner that the spoke magnet, after a turn
°C –5...+40
of the wheel, moves past the speed sensor with a clearance of
at least 5 mm, yet no more than 17 mm.
°C –10...+50
Note: If the clearance between speed sensor 17 and spoke
IP 54 (dust and splash
magnet 18 is too small or too large, or if the speed sensor 17
water protected)
is not properly connected, the speed indication e will fail, and
kg 4
the eBike drive will operate in emergency mode.
In this case, loosen the screw of the spoke magnet 18 and fas-
Intuvia
ten the spoke magnet to the spoke in such a manner that it
1 270 020 903
runs past the mark of the speed sensor at the correct clear-
ance. When the speed is still not being indicated in the speed
mA 500
indication e after this, please refer to an authorised bicycle
dealer.
V 5
Operation
°C –5...+40
°C –10...+50

Initial Operation

IP 54 (dust and splash
water protected)
Requirements
kg 0.15
The eBike system can only be activated when the following re-
quirements are met:
– A sufficiently charged battery pack is inserted (see operat-
V 6
– The drive HMI is properly inserted in the holder (see "In-
W 2.7
W 0.3
– The drive HMI is properly connected (see "Checking the
Switching the eBike System On/Off
Options for switching on the eBike system:
– If the drive HMI is already switched on when inserting it in
– When the drive HMI and the battery pack are inserted,
– When the drive HMI is inserted, press the On/Off button of
Note: When switching on the eBike system, the pedals of the
eBike must not be subject to load, as otherwise the motor out-
put capacity will be limited. The error message "Release ped-
al" is displayed in text indication c.
If the eBike system was inadvertently switched on with load
applied to the pedals, then switch it off and then on again
without load.
The drive is activated as soon as you step into the pedals (ex-
cept when in push-assistance mode, see "Switching the Push-
assistance mode On/Off", page English–4). The motor out-
put depends on the settings of the drive HMI.
ing instructions of the battery pack).
serting and Removing the Drive HMI", page English–2).
Speed Sensor", page English–2).
the holder, the eBike system is automatically switched on.
briefly press the On/Off button 5 of the drive HMI once.
the battery pack (see battery pack operating instructions).
0 276 001 YYY | (12.10.12)
English–2