Publicité
Les langues disponibles
Les langues disponibles
Precautions
SDHC/SD cards
p p Before using an unformatted SDHC or SD card, format it
first using the Center Module. When a card is formatted,
whatever has been recorded on it will be erased. If an
unformatted SDHC or SD card or an SDHC or SD card
formatted on a unit other than the Center Module is
used, it may not work properly or its performance may be
compromised.
p p When some SDHC or SD cards are used in this unit,
they may not work properly or their performance may be
compromised. Use of the recommended SDHC and SD
cards is recommended.
Recommended SDHC and SD cards
Manufactured by Panasonic Corporation (sold separately)
SDHC cards: 4 GB, 8 GB, 16 GB, 32 GB
SD cards: 2 GB
(Excluding miniSD cards and microSD cards)
p p In many cases when SD cards are formatted or their data
is erased or deleted using the functions of the Center
Module or a personal computer, the data on the cards
may not be erased completely. Before handling a card
over to another party, it is recommended that you use
a commercially available PC software application for
erasing data to erase the data on the card completely.
p p When SD cards are to be disposed of, either break them
physically or erase the data on them completely, separate
them in the garbage and dispose of them following the
regulations that are enforced in the locality concerned.
Cleaning the touch panel
p p It is recommended that the touch panel be cleaned at
regular intervals.
p p If there is any noticeable dirt, dust, oil, grease, etc. on the
touch panel, clean it immediately.
p p Wipe off the dirt or dust gently using a soft dry cloth.
p p You may damage the LCD display if you wipe or press the
touch panel too forcefully or subject the display to impact
or heavy loads.
p p Do not use liquid or spray cleaners. The touch panel
functions may be impaired as a result.
p p Do not allow products made of rubber or PVC to remain
in contact with the touch panel for prolonged periods of
time. Doing so may cause discoloration or deterioration.
p p Do not use benzene, paint thinners, adhesives, alkali- or
alcohol-based cleaning agents, glass cleaners, waxes,
abrasive cleansers, powdered cleaners, insecticides, etc.
Doing so may cause colors and texture to be degraded.
(When using a chemical cloth for cleaning, read the
caution provided with the chemical cloth product.)
10
WX-CC411_PGQX2068ZA_IG.indb
10
w Installation precautions
p
WARNING:
In order to safeguard against injury, this
device must be mounted on a wall, following the steps in
the Operating Instructions.
Panasonic assumes no responsibility for injuries or
property damage resulting from failures arising out of
improper installation or operation inconsistent with this
documentation.
Avoid installing in the following locations.
p p Locations exposed to direct sunlight
p p Locations subject to having strong vibration or impact
p p Locations which are not level
p p Locations under the air conditioner
p p Locations near the fryer
p p Locations near the grill
p p Locations where a chemical agent is used such as a
swimming pool
p p Locations near magnetic field sources such as a
television or speakers
p p Locations where condensation forms easily, where
temperature changes greatly, humid places
p p Locations subject to dust
p p Locations subject to water splash or spray
p p Locations where radiation or x-ray emissions are produced
The accessory power cord is to be used only with this unit.
Do not use it for any other devices. Similarly, do not use the
power cords of other devices with this unit.
Grounding
Confirm that the wire is connected from the SIGNAL GND
terminal to earth ground. A grounding connection must be
made before connecting the power plug or this product to
the main power supply. When disconnecting the grounding
wire, make sure that the power plug of this product is
disconnected from the main power supply.
Power supply used
The supply voltage of this unit is AC 100 V to 120 V
(50 Hz/60 Hz). Connect this unit to a power supply with a
sufficiently high capacity.
To cut the power supply
This product has no power switch. To cut the power supply,
unplug the power plug of the product from the AC outlet. If
it is hard to unplug the power cord due to the installation
conditions, connect the power cord of the product to the AC
outlet via the circuit breaker of a distribution board or to the
AC inlet socket of a power supply control unit.
Be sure to connect the power cord via any of the following
breaking devices:
p p Connect the power cord via a power supply control unit.
p p Install the product near a power outlet, and connect the
power cord via the power plug.
p p Connect the power cord to the breaker with contact gap
of 3.0 mm or more of a distribution board. The breaker
shall be able to shut down all the poles of the main power
supply except the ground protective conductor.
Setting the time
Before operating this unit, you must set the time. For how
to set the time, refer to the Operating Instructions <Setup
Instructions>.
2016/05/18
13:30:25
Publicité
