Husqvarna 455 Rancher II Manuel D'utilisation page 43

Recommended cutting equipment for USA
Following is a list of recommended cutting equipment for Husqvarna chain saw models 455 Rancher II, 455e Rancher
II, 455e Rancher II TrioBrake, 460 Rancher II and 465 Rancher II. These chain saw models equipped with either of the
listed guide bar and saw chain combination(s), fulfills the requirements according to ANSI B175.1-2000 (Gasoline
Powered Chain Saws - Safety Requirements).
The following list is the chain saw manufacturers recommendations. There may be other combinations available, which
will also achieve kickback reduction.
Chain saw models Husqvarna 455 Rancher II, 455e Rancher II, 455e Rancher II TrioBrake, 460 Rancher II and 465
Rancher II met the kickback performance requirements of ANSI B175.1-2000 when tested with the combinations of bars
and saw chains listed below. The saw chains Husqvarna H80 and H81 are also classified as low kickback saw chains
since they met the requirements for low kickback saw chain outlined in ANSI B175.1-2000. We recommend to use only
the listed combinations of bars and chains for chain saw models Husqvarna 455 Rancher II, 455e Rancher II, 455e
Rancher II TrioBrake, 460 Rancher II and 465 Rancher II. Other chain saw models may not meet the kickback
requirements when equipped with the listed guide bar and saw chain combinations.
Recommended cutting equipment for Canada
Following is a list of recommended cutting equipment for the Husqvarna chain saw models 455 Rancher II, 455e Rancher
II, 455e Rancher II TrioBrake, 460 Rancher II and 465 Rancher II. The listed combination(s) of powerhead, bar and saw
chain meet all requirements outlined in Canadian Standards Assosiation Z62.1-03 (Chain Saws) and Z62.3-04 (Chain
Saw Kickback).
Furthermore the saw chains Husqvarna H80 and H81 are evaluated and listed as a Type C Low Kickback Saw Chain
according to the provisions in Z62.3-04.
Kickback information
The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the
corresponding maximum nose radius of a solid bar.
As we are listing the maximum guide bar nose radius, you may use a guide bar with smaller nose radius than in our list.
For guide bars of the same length, all sprocket-nose guide bars of the same pitch and having the same number of
sprocket teeth may be considered to have equivalent kickback energy.
The following cutting attachments are approved for the models Husqvarna 455 Rancher II, 455e Rancher II and 455e
Rancher II TrioBrake.
Length, inch Pitch, inch
15
16
3/8
18
20
The following cutting attachments are approved for the models Husqvarna 460 Rancher II and 465 Rancher II.
Length, inch Pitch, inch
15
16
18 3/8
20
24
Note: For the saw chains above (if available) you are free to choose between 0.050" or 0.058" gauge drive links for the
corresponding bar, see the table below.
0.050
0.058
TECHNICAL DATA
Guide bar
Gauge, inch
0.058
Guide bar
Gauge, inch
0.058
H80 H46
H81 H42
Max. nose radius
11T
Max. nose radius
11T
H47
H48
Saw chain
Type Drive link count
56
Husqvarna H42,
60
Husqvarna H48,
68
Husqvarna H81
72
Saw chain
Type Drive link count
56
60
Husqvarna H42,
Husqvarna H48, 68
Husqvarna H81
72
84
English – 43