Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Only work with sharp and correctly sharpened saw chain.
Only work with correctly clamped saw chain.
Use claw stopper (16) as lever.
Never work above height of shoulders.
Never cut through several perches at the same time. When
releasing make sure that no other perch is touched.
If possible use a sawhorse when cutting to length.
Stab cuts shall only be carried out by instructed personal.
General notes
Switch the machine off and remove the mains
plug from the socket when
− contact of chain saw with soil, stones, nails or
other foreign substances
check immediately chain and sword
− carrying out repair works
− maintenance and cleaning
− removal of faults
− cut through connection cables
− checking of connection cables whether they are
swallowed or damaged
− transport
− clamping again the chain
− chain change
− leaving of machine (also for short-term interruption)
Maintain your chain saw with care:
− Keep your tools sharp and clean in order to be able to
work better and safer.
− Comply with the maintenance instructions and the
advices for lubrication and for the tool change.
− Keep the handholds dry and free from resin, oil and
grease.
Check the machine for possible damage:
− Before further use of the machine the protection devices
or slightly damaged parts must be checked carefully for
their proper and intended function.
− Check whether the movable parts function perfectly and
do not stick or whether the parts are damaged, All parts
must be correctly installed and fulfil all conditions to
ensure perfect operation of the chain saw.
− Damaged guards and parts must be properly repaired or
exchanged by a recognized, specialist workshop; insofar
as nothing else is stated in the instructions for use.
− Damaged or illegible security labels have to be replaced.
− Do not allow any tool key to be plugged in!
Before switching on, check always that all tools are
removed.
− Store unused equipment in a dry, locked place out of the
reach of children.
Do not carry out repair operations on the machine other
than those described in section "Maintenance" but contact
the manufacturer or authorized customer service centre
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service points.
Use only original spare parts, accessories and special
accessory parts. Accidents can arise for the user through
the use of other spare parts. The manufacturer is not liable
for any damage or injury resulting from such action.
22
Connect chain saw to power supply system only after
having finished the complete assembly.
Risk of injury!
Wear protective gloves when assembling.
Place the chain saw on a level surface and release the
chain brake. Press the front hand guard (3) against the
front handle (4). Remove the cover (10) by removing
the retaining nut (11).
Turn the chain stretching screw (12) anticlockwisely
until the chain stretching pin (21) is in its end position.
Place the guide bar. The chain stretching pin (21) must
engage in the provided hole in the guide bar.
Put the saw chain over the chain wheel (13)
insert it in the circumferential guiding groove of the
guide bar.
Attend to the correct running direction of the chain
links!
When assembling, pay attention that the chain
links are lying correctly within the guide slot and on the
chain wheel (13).
Remount the cover (10) and tighten the nut (11) hand-
tight.
Clamping the saw chain as described in section „Clamping
the saw chain"
B
e
f
o
B
e
f
o
Chain lubrication
The chain saw is not delivered filled with saw chain
adhering oil.
Never operate the chain saw without lubrication. Any
use without chain saw oil may result in damage of the
chain saw and guide bar.
The durability and cutting power of the chain depends on the
optimal lubrication. During operation the saw chain is
automatically wetted with oil.
Charging the oil tank
Put the chain saw on a suitable base.
Unscrew the oil tank lock (9).
Fill the oil tank with bio-degradable chain saw adhering
oil (app. 90 ml). The fill level can be seen on the inspection
window (17). For easier filling use a funnel.
When filling observe that no dirt reaches the oil tank.
Screw on the oil tank lock again.
.
Once you have filled the oil tank for the first
time or after it was completely emptied press the
"primer" (9) about 10 times to pump oil in the circuit.
Never use recycled oil or used oil. The guarantee expires
when using oil which is not allowed for chain saws.
A
s
s
e
m
b
l
y
A
s
s
e
m
b
l
y
r
e
t
h
e
f
i
r
s
t
c
o
m
m
i
s
s
r
e
t
h
e
f
i
r
s
t
c
o
m
m
i
s
s
and
i
o
n
i
n
g
i
o
n
i
n
g
Publicité
Chapitres
Table des Matières
