Painting; Painting In Multifinish Mode; Painting In Airless Mode; Control Panel Indicators - Titan MULTIFINISH 440 Mode D'emploi

Painting

The MultiFinish spray system has two different painting modes. The
MultiFinish mode is used for fine finish work with low to medium
viscosity materials (oil, stains, lacquers, etc...). The airless mode is used
for general painting with high viscosity materials (latex).

Painting in MultiFinish Mode

Use the MultiFinish mode for low-pressure fine finish work
(recommended pump pressure up to 1000 PSI).
1. Make sure that the airless spray hose is free of kinks and clear
of objects with sharp cutting edges.
2. Make sure the pressure control knob is in its OFF position in
the white zone.
3. Turn the compressor air pressure regulator counterclockwise
to its lowest setting.
4. Move the compressor ON/OFF switch to the ON position.
Air pressure
regulator
Compressor
ON/OFF switch
5. Move the pump ON/OFF switch to the ON position.
6. Turn the PRIME/SPRAY valve to SPRAY.
7. Turn the pressure control knob clockwise until the material
pressure gauge reads 400 PSI. The paint hose should stiffen as
paint begins to flow through it.
8. Turn the air pressure regulator clockwise until the air pressure
gauge reads 20 PSI.
9. Unlock the spray gun trigger.
10. Trigger the spray gun to bleed air out of the material hose.
11. When material reaches the spray tip, spray a test area to check
the spray pattern.
12. Adjust the spray pattern to the desired size and atomization.
a. Use the pressure control knob to control the flow of paint to the
gun.
b. Use the air pressure regulator to control the amount of atomization
air available to the gun.
c. Use the pattern adjustment knob on the gun to fine tune the spray
pattern.
NOTE: Refer to the spray gun Owner's Manual for
information on the operation of the gun.

Painting in Airless Mode

Use the airless mode for general high-pressure spraying (pump
pressure from 500 to 3300 PSI).
1. Make sure that the airless spray hose is free of kinks and clear
of objects with sharp cutting edges.
2. Make sure the pressure control knob is in its OFF position in
the white zone.
3. Turn the PRIME/SPRAY valve to SPRAY.
4. Move the pump ON/OFF switch to the ON position.
5. Turn the pressure control knob clockwise to its highest
setting. The paint hose should stiffen as paint begins to flow
through it.
6. Unlock the spray gun trigger.
7. Trigger the spray gun to bleed air out of the material hose.
8. When material reaches the spray tip, spray a test area to check
the spray pattern.
English
9. Use the lowest pressure setting necessary to get a good spray
pattern. If the pressure is set too high, the spray pattern will
be too light. If the pressure is set too low, tailing will appear or
the paint will spatter out in "gobs" rather than in a fine spray.
Good spray pattern
Paint tailing pattern

Control Panel Indicators

The following is a description of the control panel indicators.
Motor
Running
Motor
Running
Indicator
MIN
PSI (Bar)
RAPID
CLEAN
Pressure Indicator
The pressure indicator shows the current operating pressure of the
sprayer. It has three different indications: blinking yellow, solid
yellow, and solid green.
Blinking Yellow
When the pressure indicator is blinking yellow, the sprayer is
operating between 0 and 200 PSI. A blinking yellow pressure
indicator means:
• The sprayer is plugged in and turned "ON"
• The sprayer is at priming pressure (little or no pressure)
• It is safe to move the PRIME/SPRAY valve between positions
• It is safe to change or replace the spray tip
NOTE: If the pressure indicator begins blinking yellow
when the pressure control knob is set at a higher
pressure and the PRIME/SPRAY valve is in the
SPRAY position, either the spray tip is worn or the
sprayer is in need of service/repair.
Solid Yellow
When the pressure indicator is solid yellow, the sprayer is operating
between 201 and 1900 PSI. A solid yellow pressure indicator means:
• The sprayer is at the proper pressure setting for spraying stain,
lacquer, varnish, and multi-colors
• If the pressure indicator goes to solid yellow when the
pressure is set so that it starts at solid green, it indicates one of
the following:
a. Tip Wear Indicator — when spraying with latex or at high pressure
the solid yellow appears. This means the tip is worn and needs to
be replaced.
b. Tip Too Large — when a tip that is too large for the sprayer is put
in the gun, the pressure indicator will turn from solid green to solid
yellow.
c. Fluid Section Wear — if a solid yellow pressure indicator appears
when using a new tip and the pressure is set at maximum, service
may be required (worn packings, worn piston, stuck valve, etc...).
6
0 2 - 0 0 P I S — Blinking Yellow
A R I A S S S I E T D — Solid Yellow
AIRLESS — Solid Green
Pressure
Indicator
MAX
PSI (Bar)
© Titan Tool Inc. All rights reserved.