Operating The Front Caster; Pressure Relief Procedure; Cleanup - Titan SPEEFLO PowrLiner 1800M Notice D'utilisation

POSSIBLE INJECTION HAZARD. Do not spray
without the tip guard in place. Never trigger the
gun unless the tip is in either the spray or the
unclog position. Always engage the gun trigger
lock before removing, replacing or cleaning tip.
22. Turn on the sprayer.
23. Increase the pressure by turning the pressure control knob
slowly clockwise. Test the spray pattern and line position
on a long piece of roofing felt or cardboard.
a. Adjust the pressure control knob until the spray from the
gun is completely atomized. Try to keep the pressure
control knob at the lowest setting that maintains good
atomization.
NOTE: Turning the pressure up higher than needed to
atomize the paint will cause premature tip wear
and additional overspray.
b. Check for proper line width and position. If adjustment
to the position of the spray gun is required, refer to the
"Setup" procedure earlier in this section.
24. Make sure that the spray gun completely shuts off when
the gun trigger is released. If adjustment to the trigger
tension is required, refer to the "Adjusting the Trigger
Tension" procedure earlier in this section.

Operating the Front Caster

PowrLiner 1800M
The front caster on the cart is designed to track the sprayer in
either a straight line or allow free motion.
1. To lock the the front caster in the straight line position,
rotate the lever above the caster clockwise until it stops.
2. To allow free motion, turn the lever above the caster
clockwise approximately 1/2 turn or until the caster rotates
freely.
PowrLiner 2800M
The front caster on the cart is designed to track the sprayer in
either a straight line or allow free motion. Standing behind the
sprayer, the trigger on the left handle of the cart controls the
operation of the front caster.
1. To lock the front caster in the straight line position,
squeeze then release the caster trigger and move the
sprayer forward.
2. To allow free motion of the front caster, squeeze and hold
the caster trigger.
NOTE: To lock the front caster in free motion mode,
squeeze and hold the caster trigger and then
push in the locking button on the side of the
trigger. Once the locking button is pushed in,
the caster trigger can be released. To release the
locking pin, squeeze the caster trigger.

Pressure Relief Procedure

Be sure to follow the Pressure Relief Procedure
when shutting the unit down for any purpose,
including servicing or adjusting any part of the
spray system, changing or cleaning spray nozzles,
or preparing for cleanup.
1. Lock the gun by turning the gun trigger lock to the locked
position.
2. Turn off the sprayer by moving the pump ON/OFF switch
to the OFF position.
3. Turn off the engine by moving the engine ON/OFF switch
to the OFF position.
4. Turn the pressure control knob counterclockwise to its
lowest setting.
5. Unlock the gun by turning the gun trigger lock to the
unlocked position.
© Titan Tool Inc. All rights reserved.
6. Hold the metal part of the gun firmly to
the side of a metal container to ground
the gun and avoid a build up of static
electricity.
7. Trigger the gun to remove any pressure
that may still be in the hose.
8. Lock the gun by turning the gun trigger lock to the locked
position.
9. Move the PRIME/SPRAY valve to the PRIME position.

Cleanup

Special cleanup instructions for use with
flammable solvents:
• Always flush spray gun preferably outside and at least one
hose length from spray pump.
• If collecting flushed solvents in a one gallon metal
container, place it into an empty five gallon container, then
flush solvents.
• Area must be free of flammable vapors.
• Follow all cleanup instructions.
IMPORTANT: The sprayer, hose, and gun should be cleaned
thoroughly after daily use. Failure to do so permits material
to build up, seriously affecting the performance of the unit.
Always spray at minimum pressure with the gun
nozzle tip removed when using mineral spirits or
any other solvent to clean the sprayer, hose, or
gun. Static electricity buildup may result in a fire
or explosion in the presence of flammable vapors.
1. Follow the "Pressure Relief Procedure" found in the
Operation section of this manual.
2. Remove the gun tip and tip guard and clean with a brush
using the appropriate solvent.
3. Place the siphon tube into a container of the appropriate
solvent (refer to recommendations of the material
manufacturer). An example of the appropriate solvent is
water for latex paint.
4. Place the return hose into a metal waste container.
5. Move the PRIME/SPRAY valve to its PRIME position.
6. Move the engine ON/OFF switch to the ON position and
start the engine.
7. Turn on the sprayer by
moving the sprayer ON/OFF
switch to the ON position.
8. Slowly turn the pressure
control knob clockwise to
increase the pressure until
fluid starts to come out of the
return hose.
9. Allow the solvent to circulate
through the sprayer and
flush the paint out of the
return hose into the metal waste container.
10. Turn the pressure control knob fully counterclockwise to
its lowest setting.
11. Turn off the sprayer by moving the ON/OFF switch to the
OFF position.
12. Move the PRIME/SPRAY valve to its SPRAY position.
13. Turn on the sprayer.
14. Turn the pressure control knob slowly clockwise to
increase pressure.
Ground the gun by holding it
against the edge of the metal
container while flushing. Failure to
do so may lead to a static electric
discharge, which may cause a fire.
7
Sprayer Pressure
ON/OFF Control
Switch Knob
English