Items Supplied; Proper Use - EINHELL RT-TS 1825 U Mode D'emploi

Masquer les pouces Voir aussi pour RT-TS 1825 U:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 26
Anleitung_RT_TS_1825_U_SPK1:Anleitung TKS 18-250 UV SPK 1
1. Layout
1 Saw table
2 Saw blade guard
3 Push stick
4 Saw blade
5 Splitter
6 Table insert
7 Parallel stop
8 Handwheel
9 Adjusting and locking grip
10 Base frame
11 ON/OFF switch
12 Eccentric lever
13 Extractor hose
14 Cross stop
15 Screw with wing nut
16 Extractor adapter
20 Fixing screw
21 Clamping screws
35 Length extension table
36 Width extension table
43 Rubber feet
50 Table support

2. Items supplied

Bench-type circular saw
Carbide-tipped saw blade
Parallel stop
Cross stop
Push stick

3. Proper use

The bench-type circular saw is designed for the
slitting and cross-cutting (only with the cross stop) of
all types of timber, commensurate with the machineʼs
size.
The machine is not to be used for cutting any type of
roundwood.
The machine is to be used only for its prescribed
purpose.
Any other use is deemed to be a case of misuse.
The user/operator and not the manufacturer will be
held liable for damage and/or injuries of any kind that
result from such misuse. The machine is to be
operated only with suitable saw blades (saw blades
made of HM or CV) It is prohibited to use any type of
HSS saw blade and cutting-off wheel. To use the
machine properly you must also observe the safety
regulations, the assembly instructions and the
operating instructions to be found in this manual.
05.06.2008
All persons who use and service the machine have
to be acquainted with this manual and must be
informed about the machineʼs potential hazards.
It is also imperative to observe the accident
prevention regulations in force in your area.
The same applies for the general rules of
occupational health and safety.
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
Important!
When using the equipment, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating instructions and
safety regulations with due care. Keep this manual in
a safe place, so that the information is available at all
times. If you give the equipment to any other person,
hand over these operating instructions and safety
regulations as well. We cannot accept any liability for
damage or accidents which arise due to a failure to
follow these instructions and the safety instructions.
The manufacturer shall not be liable for any changes
made to the machine nor for any damage resulting
from such changes.
Even when the machine is used as prescribed it is
still impossible to eliminate certain residual risk
factors. The following hazards may arise in
connection with the machineʼs construction and
design:
Contact with the saw blade in the uncovered
saw zone.
Reaching into the running saw blade (cut
injuries).
Kick-back of workpieces and parts of work-
pieces.
Saw blade fracturing.
Catapulting of faulty carbide tips from the saw
blade.
Damage to hearing if ear-muffs are not used as
necessary.
Harmful emissions of wood dust when used in
closed rooms.
8:25 Uhr
Seite 17
GB
17

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

43.406.4801017

Table des Matières