Christopeit Sport TM650S Notice De Montage Et D'utilisation page 19

INDOOR TRAININGS APP
The product can be used with the Kinomap app. This enables enter-
taining and interactive training with Android or IOS devices and saving
training data.
Sport, coaching, gaming and eSport are the keywords of the Kinomap
app. This contains many kilometers of real film material to exercise inside
as if you were outside; Tracking routes and analysis of your performance;
Coaching content; Multiplayer mode; new posts daily; Official indoor ra-
ces and more ... The APP thus contains approx. 100,000 videos recorded
by athletes and 200,000 km of accumulated tracks for cycling, running or
rowing for currently approx. 270,000 members from all over the world.
Download the app and connect
Scan the adjacent QR code with your smartphone / tablet or use the se-
arch function at the Playstore (Android) or APP Store (IOS) to download
the Kinomap APP. Register and follow the instructions in the APP.
Activate Bluetooth on the smartphone or tablet and select the device
manager via the menu in the APP and then select the „treadmill" catego-
ry. Then select your type designation via the manufacturer logo „Chris-
topeit Sport" in order to connect the sports equipment. Depending on
the sports equipment, different functions are recorded by the APP via
Bluetooth or data is exchanged.
Attention: The Kinomap APP offers a free trial version for 14 days. After
that, fees will apply which are listed on the Kinomap homepage. Further
information can be found at: https://www.kinomap.com/en/
Meanings of error message codes
In case of malfunctions may adjoining list of error messages help for savvy
people to get function back. Basically, electrical repairs only in compliance
with the relevant safety rules which exists. For more information and
assistance in case of malfunctions with our service department (contact
details see last page.)
Problem Potential reasons
---- The safety lock is removed
E01 Communication abnormality: abnormal
communication between the controller and
the electronic meter after powering on.
E02 Voltage-proof protection:
E03 No sensor signal:
E05 Over-current protection:
E07/E08 EEPROM defect
Motor The motor cable is damaged or connected
will not incorrectly.
start The fuse on the control board has been
damaged or dropped.
The control board is defect.
The motor is defect.
IOS AND ANDROID APP
Solutions
1. Put the safety clip in position
2. Change the safety clip or safety clip socket at computer.
3. If it's still not ok, than change the computer.
1. Switch off the treadmill and plug out AC cable.
2. Check each section of communication cables from the electronic meter to the controller and ensure
that all cables are well connected.
3. Check whether cables between the electronic meter and the controller are damaged; if yes, replace the
damaged wire.
1. Switch off the treadmill and plug out AC cable
2. Check whether the power supply voltage is less than 50% of the normal value. Please ensurecorrect
voltage and test again.
3. Check whether the controller emits the odor of burning; if yes, replace the controller.
4. Check whether motor cables are well connected; re-connect motor wires.
1. Switch off the treadmill and plug out AC cable.
2. Check whether the sensor cable is well plugged or whether it is damaged; plug it well or replace the
sensor.
1. Check whether power supply voltage specifications is inconsistent or too low and use correct voltage
specifications for re-test.
2. System self-protection is triggered under excessive current caused by the excessive load more than
the rated value, or some place of the treadmill is jammed so that the motor cannot rotate; thus, the
system start up self-protection against excessive current under excessive load; adjust the treadmill and
restart it.
3. Check whether there is over-current sound or burning odor when the motor is running; replace the
motor.
4. Check whether the controller emits abnormal odor; replace it if yes.
Replace the control board.
Check the motor cable.
Check the fuse. Reinsert it, or replace the fuse.
Replace the control board.
Replace the motor.
19