Using I/O Link.a - Pioneer PureVision PDP-506XDE Mode D'emploi

Masquer les pouces Voir aussi pour PureVision PDP-506XDE:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Enjoying through External Equipment
13
NOTE
• If you select a parameter other than "Auto", make such a
setting that results in natural colour.
• If no image appears, specify another digital video signal type.
• For the digital video signal types to be specified, check the
operation manual that came with the connected equipment.
To specify the type of audio signals:
When you use the INPUT 3 HDMI terminal, use the following
procedure to specify the type of audio signals.
1
Repeat steps 1 to 3 provided for "To activate the HDMI
terminal."
2
Select "Audio" ( /
3
Select the type of audio signals ( /
• If you select "Auto", an attempt will be made to identify
the type of audio signals when audio signals are
received.
Item
Description
Auto
Automatically identifies input audio signals.
(factory default)
Digital
Accepts digital audio signals.
Analogue
Accepts analogue audio signals.
4
Press HOME MENU to exit the menu.
NOTE
• The INPUT 4 HDMI terminal accepts only digital audio
signals.
• If no sound is output, specify another audio signal type.
• For the audio signal types to be specified, check the
operation manual that came with the connected equipment.
• Depending on the equipment to be connected, you also need
to connect analogue audio cables.
62
En
then ENTER).
then ENTER).

Using i/o Link.A

The Plasma Display System incorporates three typical i/o
Link.A functions for smooth connections between Media
Receiver and other audiovisual equipment.
One Touch Play
While the Plasma Display System is in standby mode, it
automatically turns on and plays back images from the
audiovisual source (e.g. VCR, DVD).
WYSIWYR (What You See Is What You Record)
When the remote control unit of the connected VCR has the
WYSIWYR button, you can automatically start recording by
pressing the WYSIWYR button.
Preset Download
Automatically transfers channel preset information from the
tuner on the Plasma Display System to the one on the
connected audiovisual equipment (e.g. VCR) via the INPUT 2 or
3 terminal.
NOTE
• The i/o Link.A functions work only when the audiovisual
equipment is connected to the INPUT 2 or 3 terminal on the
Media Receiver with i/o Link.A via a fully wired 21-pin SCART.
• Either INPUT 2 or 3 is available for i/o Link.A, depending on
the switch on the rear of the Media Receiver.
• Using this switch, select the input terminal to which
recording equipment such as a VCR has been connected.
• Refer to operation manuals of each external equipment for
the details.
• If a SCART cable has been connected to the INPUT 3
terminal with the i/o Link.A activated, input signals (other
than Component) are automatically identified and displayed.
If the i/o Link.A has been deactivated, Video is always
selected for signals other than RGB because the system
cannot identify among RGB, Y/C (S-Video), and CVBS (Video)
signals; for example, receiving Y/C (S-Video) signals results
in monochrome display.
Media Receiver (rear view)
I N
OUT
SERVICE ONLY
CONTROL
INPUT 1
ANT
i /o link.A
SELECT
INPUT
2
3
INPUT 1
i / o link.A
SELECT
SCART cable
INPUT
(commercially available)
2
3
VCR or DVD Recorder (DVR)
OUT
IN
OPTICAL
DIGITAL OUT COMMON INTERFACE
ANT(DIGITAL)
INPUT 2
Y
P
P
R-AUDIO-L
SUB
B
R
WOOFER
COMPONENT VIDEO
AUDIO OUTPUT
INPUT 3
HDMI
HDMI
BLACK
WHITE
INPUT 4
SYSTEM CABLE

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Purevision pdp-436xde

Table des Matières