English; Electrical Chain Grinder; Machine Characteristics; Data And Models - Tecomec 135 jolly Manuel D'instructions

ENGLISH

A copy of this manual is delivered with each grinder.
NB: The descriptions and illustrations contained in this manual are not binding. The manufacturer reserves the right to bring
about any modifications without updating the handbook.

ELECTRICAL CHAIN GRINDER

type 135 jolly TECOMEC - type 135 jolly JOKER - type FL 136 TECOMEC

MACHINE CHARACTERISTICS

- Manufacturer: Tecomec SpA - Via Secchi, 2 - 42011 Bagnolo in Piano - Reggio Emilia - ITALY
- Machine: Electrical chain grinder

DATA AND MODELS

Models
Input
Rated power
Tool RPM
Current
Type of lamp
Sound pressure level
Level of vibrations transmitted to the handle
Complete machine weight
Grinding wheel dimensions
Chain types
- Accessories supplied: in the packing box you will find a pack containing grinding wheels (thickness: 3.2 - 4.7 - 6 mm); a tool set with
1 Allen wrench (No. 4) - 1 Allen wrench No. 5 - 1 wheel dresser - 1 template – 1 handwheel (2) – 1 additional guard (15) – 1 grip (16),
screws and washers. You will also find, as loose component, the main wheel guard (12).

INTRODUCTION

Keep this handbook with care.
To ensure the correct use of the grinder and to prevent accidents, do not start working without having read this handbook carefully.
This handbook explains the operation of the machine components and provides instructions for carrying out the checks and mainte-
nance required.
WARNING – Any maintenance operations not described in this handbook must only be carried out by an authorized service
center. To guarantee the efficient and consistent operation of your grinder, worn or broken parts must only be replaced using ORIGINAL
SPARE PARTS.

SAFETY RULES

WARNING – When correctly used, your grinder is a fast, easy, and efficient work tool. For pleasant and safe working, carefully
comply with the safety rules listed below, as well as with those provided throughout the handbook.
1 - The grinder must only be used by adults. Users must be in good physical condition and familiar with the instructions for use.
2 - Never wear rings, bracelets and/or loose clothing that could come into contact with the grinding wheel.
3 - Always wear gloves and protective eyewear while operating the grinder and while sharpening the wheel.
4 - Never stop the grinding wheel with your hands, even after turning off the motor.
5 - Check that the plug is disconnected when fitting the grinding wheel and during maintenance or transport.
6 - Never start the grinder without the main wheel guard (12) and the additional screen (15) in place. The two guards are supplied loose
and must be installed by the operator, because they are considered essential safety components. The Manufacturer may not be
held liable for any fortuitous accident caused by failure to install on the machine the safety devices described above.
7 - Check that the voltage and frequency indicated on the grinder's data tag correspond to the mains values.
8 - Never use defective or non-standard cables, plugs or extension cables.
9 - Remove the plug from the mains immediately if the cable is damaged or cut. For cable repair or replacement, contact your author-
ized dealer or service center. The power supply cable is complete with terminals – with protection. For internal electrical connection
insert the feeding cable terminals directly into the switch. The electrical connection to the mains must be made in order to prevent
damages by people or vehicles which could endanger both their safety and yours.
10 - Before starting up the grinder, check that the working area is free of tools or other objects.
11 - Check the cable position during operation, making sure that it remains outside the grinding wheel operating area and that it is not
energized. Never work near other electrical cables.
12 - Never advance the chain with your left hand until the grinding wheel has moved entirely outside the working area.
13 - Do not allow other people to remain near the grinder during its operation or to touch its supply cable.
14 - Always keep the hand-grips clean and dry.
15 - Before starting the grinder, check that the grinding wheel is correctly secured and out of the working area.
16 - To work with the machine, check that it is properly secured, on a bench or to the wall.
17 - Always work in a stable and safe position, and be particularly careful.
18 - Always comply with maintenance instructions.
1135328_R05_U&M_Jolly-Joker230V.indd 11
Issued by the Technical Assistance and Publications Office
ALL RIGHTS RESERVED
type 135 jolly TECOMEC
230V - 50Hz - 1 ph
W
214
2800 min
3A
W
15
77dB (A)
< 2,5 m/s
58.8N (6 kg)
Øint.= 22,3mm - Øext.= 145mm - H= 3.2 - 4.7 – 6 mm
1/4" - .325" – 3/8" - .404" – 1/2"
type 135 jolly JOKER
230V - 50Hz - 1 ph
W
214
-1 2800 min -1
3A
W
15
77dB (A)
2 < 2,5 m/s 2
58.8N (6 kg)
(3/4"available with special grinding wheel and vise)
GB
type FL 136 TECOMEC
120V - 60Hz - 1 ph
W
285÷300
3400 min -1
1,5A
W
15
77dB (A)
< 2,5 m/s 2
58.8N (6 kg)
11
22/02/2011 10.37.09