Extra Protection; Packaging; Removing The Packaging And Recycling; Installation - Dru Verwarming METRO 80E Manuel D'installation Et D'entretien

Have a cracked or broken glass pane replaced by your
installer.
When performing maintenance and service work, you
should always remove the power plug from the wall
socket (fi gure 1).
In case of damages to the appliance, immediately consult
the supplier, before it is installed and put into operation.
Do not use the appliance outdoors.
Do not place the appliance in a moist environment or
near a bath, shower or pool.
The warm air outlet and cold air inlet may never be
completely or partly blocked (see fi gure 2).
The appliance is suitable for 230V, 50Hz and has a maxi-
mum connecting value of 1500 watts at 230V.
You should always be able to reach the plug after instal-
lation.
The wall socket to which the appliance will be connec-
ted, must be earthed (see fi gure I).
Do not place any objects in front of the appliance as
they could be affected by the heat (see fi gure 2).
Never place the power cable near the hot air outlet.
Do not let children or infi rm persons near the appliance
without supervision and keep the remote control out of
their reach.
Do not use this appliance in combination with other
control equipment, such as timers, thermal controllers
or programmed controllers, which will automatically
switch on the appliance. The appliance could be covered
or someone may have placed something under or in
front of the appliance, which could result in fi re.
In case of a malfunction, remove the plug from the wall
socket.
Do not hang wet clothes, towels etc. on or near the
appliance in order to dry them!
When you use the remote control to put the appliance
in standby mode, a bit of electric current will continue
to pass through the appliance, we recommend use of the
on/off switch to switch off the appliance.
Do NOT use the appliance at room temperatures below
2ºC and above 40ºC.
Do NOT use the appliance when the atmospheric
humidity is higher than 80%.
Do NOT use the appliance at a height above 2,000
metres.
Caution: The appliance weighs approximately 50 kg, do
not try to move the appliance without the assistance of
a second person.
INSTALLATION AND SERVICE MANUAL

3.4 Extra protection

If the appliance is installed in a room where small
children or infi rm people are staying, we recom-
mend screening off the appliance and storing the
remote control in a safe place.

4. Packaging

Het toestel mag alleen getransporteerd worden in de daar-
voor bedoelde verpakking. Door geen gebruik te maken
van de juiste verpakking kan er transportschade ontstaan
waardoor gevaarlijke situaties kunnen ontstaan.

5. Removing the packaging and recycling

When receiving the appliance, you must check if the
packaging is undamaged. If this is not the case, you must
contact your supplier. Never use the product if the pac-
kaging is damaged!
Check the appliance for damages during transport. If
there is any damage at all, contact your supplier and
never use the appliance!
Keep the packaging materials until the appliance is instal-
led and tested.
The packaging must be disposed of in accordance with

regulations.

6. Installation

Read this manual carefully to ensure a proper and safe
operation of the appliance.
Install the appliance in the order described in this chapter.
6.1 Regulations
- Observe the applicable (installation) regulations.
- Observe the regulations/instructions in this manual.
6.2 Checking the fl ame picture
- Place the supplied power cable in the wall socket.
- Switch on the appliance by using the switch in the left
top of the appliance.
- Check whether the fl ame picture is visible.
- Use the remote control to check if the intensity of the
fl ame picture can be regulated
(see chapter 11- Remote control).
6.3

Checking the heating module

A thermal cut-out is incorporated in the heating elements
in order to avoid overheating. This thermal cut-out can
switch off the heating when the hot air outlet is blocked
(see fi gure 2). When cooled down, the heating element
will switch on again automatically. If the thermal cut-out
is activated with no reason, you should contact your sup-
plier.
After the heating element is switched off, the ventilator will
continue to rotate for a few seconds in order to cool the
element. Because of this feature, it is important that the
11
Metro 80E/120E