Proper Use - Scheppach HF50 Traduction Des Instructions D'origine

Proper Use

The router is ideal for machining wood and plastic and
also for cutting out knots, cutting grooves, removing re-
cesses, copying curves and logos, etc. The router must
not be used for machining metal, stone, etc.
The equipment is to be used only for its prescribed pur-
pose. Any other use is deemed to be a case of misuse.
The user / operator and not the manufacturer will be li-
able for any damage or injuries of any kind caused as a
result of this.
Please note that our equipment has not been designed
for use in commercial, trade or industrial applications.
Our warranty will be voided if the machine is used in
commercial, trade or industrial businesses or for equiva-
lent purposes.
Attention: The use of an accessory or an attachment
not recommended in these operating instructions can
lead to bodily injuries.
This product may be used only for the intended purpose.
Any application not described in these operating instruc-
tions is regarded as inappropriate use. The operator, and
not the manufacturer, is responsible for all damage or in-
juries as a result of inappropriate application.
• Support long work pieces correctly.
• Keep the table openings as small as possible regard-
ing the size of the cutting tool by use of the correct
table rings.
• Additional aids, like horizontal pressure means, are to
be used for working on narrow work pieces.
• Do not stand the machine in rain.
Assembly
Attention
Before doing any setting or maintenance work pull the
power supply plug.
Fixing the machine
When using the machine it is recommended to fasten it
to a work bench by means of the four holes
1 Holes must be drilled in the assembly surface, consid-
ering the spacing of the two fixing holes in the base.
2 Each leg must be tightened with bolts (not supplied).
3 The bolts must be sufficiently long: Take into account
the thickness of the working surface onto which the
machine has to be fastened.
4 Use the washers and screw the working surface on
with the nuts.
5 The working surface must be sufficiently large in order
to prevent tilting of the unit during working.
Attention: Before starting work, check the solidity of
the working surface.
20 GB
Moulding fence components:
A. 1 Base holder
A. 2 Bracket
B Mounting
C Fence 2x
D Pressure bar
E Extraction connection piece
Attachment parts for moulding fence
5 Plastic cap nuts M6
5 Washers 6mm
5 Carriage bolts M6 x 25
Table attachment
1 Carriage bolt M6 x 20
1 Carriage bolt M6 x 40
2 Plastic cap nuts M6
2 Washers 6mm
Mounting the moulding fence, Fig. 3–5
Assembly of the moulding fence:
The moulding fence has been shipped in the carton box
disassembled. Before starting work, it must be assem-
bled and fitted onto the working table.
Step 1: Assembly of part A and B
Push the mounting (B) onto the base holder (A. 1) in the
groove provided (see Fig. 4). Now insert a carriage bolt
M6 x 25 into the hole and screw on a plastic cap nut with
a washer.
Step 2: Fitting the stop bars C
Insert two carriage bolts into the attachment holes and
screw them on finger tight with a washer and a plastic
cap nut. Then, with the groove, push the fence onto the
carriage bolt caps. Now tighten both plastic cap nuts.
Carry out the same process on the other side of the
fence. Make sure you attach the fences (C) in the correct
direction. Check that the fences (C) and the base holder
and bracket (A. 1 + A. 2) are at the same height.
Step 3: Fitting pressure part D, Fig. 6.1
Attach the pressure bar (D) to the fence with 2 carriage
bolts, 2 washers and 2 plastic cap nuts.
Step 4: Fitting the transparent tool guard, Fig. 6.2
To do this, the pressure bar Fig. 6 must be removed.
The transparent tool guard protects you from a possible
contact with the cutting knives.
Put the transparent guard onto the moulding fence and
secure it with a pin in the hole provided.
Test whether the guard can be folded down and is se-
curely fixed.
Your moulding fence is now ready for use.
Fig. 7.1 + 7.2
Fixings for pressure device
F Pressure frame 2x
G Square mounting plate 2x
H Square bolt 2x
I Clamp for square bolt 2x