DeWalt P35s Mode D'emploi page 10

PROPER MAINTENANCE AND CLEANING
MAKE SURE THE TOOL IS NOT LOADED. BE SURE THE TOOL IS NOT HOT PRIOR TO ATTEMPTING
DISASSEMBLY OR CLEANING.
DAILY FUNCTION TEST
Check the functioning of the tool, without a powder load or fastener in the tool, by pushing down against
the work surface, pulling the trigger, and releasing the tool from the work surface. Function the unloaded
tool several times and insure that the breech parts and firing mechanism operate freely before fastening
with the tool.
Your DEWALT Authorized representative should be asked to assist the first time you disassemble and
clean your tool. If you ever have any trouble reassembling the tool, or have any doubt about worn parts, call
your DEWALT Authorized Powder Distributor.
CLEANING
AIl parts should be cleaned with detergent oil and the wire brushes supplied with your tool kit. Remove heavy
dirt build-up with the brush. After cleaning with oil, all parts should be wiped thoroughly dry. Excess oil will
tend to collect dirt and dust. Wear eye protection when cleaning the tool. The piston rod, barrel assembly,
and receiver should all be cleaned of excess dirt on a daily basis. Check the condition of the piston for
damage from wear and deformation.
To maintain this tool in good working condition, it is necessary to disas semble and clean the entire tool if
dirt is evident in the breech face, or if the tool appears to lose power. All parts should be cleaned with oil and
wire brushes. Remove heavy dirt. All parts should be wiped thoroughly dry after cleaning with oil.
General tool mainte nance should be performed at six month intervals or more frequently as required by the
frequency of tool use.
P35s SPARE PARTS LISTING
# DESCRIPTION
1
52200-PWR Piston W/Ring 21/SDF-Standard
2
52106-PWR
3
52204-PWR Guide 21/F3-1Full Size
4
52206-PWR Baseplate 21/SI Full Size
5
52208-PWR
6
52210-PWR Baseplate 21/S2 Limited Access
7
52212-PWR Guide 21/F-2-1Limited Access
8
52214-PWR Annular Spring
9
52118-PWR
10
52120-PWR
11
52122-PWR Steel Annular Ball
12
52124-PWR Release Lever Pin
13
52126-PWR Lever Guide Kit
14
52128-PWR Threaded Pin
15
52130-PWR Advance Lever
23
22
P35s
16
52132-PWR
17
Piston Ring 52134-PWR
18
52138-PWR
19
52140-PWR
20
Piston Stop 52142-PWR
21
52144-PWR
22
52146-PWR
23
52148-PWR
Trigger
24
52150-PWR
Shear Clip
25
52152-PWR
26
52154-PWR
27
52156-PWR
†
28
52158-PWR
29
52216-PWR
30
52218-PWR
27
39
21
# DESCRIPTION
Advance Lever Guide
Sear Spring
Firing Pin Return Spring
Strip Pressure Ball & Spring
Advance Lever Spring
Rear Spring Kit
Sear
Firing Pin
End Cap
Pressure Pin
Compression Spring
Firing Pin Nut
Front Allen Cap Screw (2)
Piston Guide
Steel Liner Assembly
24
24
# DESCRIPTION
31
52220-PWR Trigger Return Spring
32
52222-PWR
33
52168-PWR Support Strip Assembly
34
52170-PWR
35
52172-PWR
36
52174-PWR Trigger Return Spring
37
52176-PWR Advance Lever Bushing
39
52180-PWR Spring Detent (2)
40
52182-PWR Cheese Head Screw (2)
41
52184-PWR Handle Allen Screw
42
52186-PWR
43
52181-PWR Firing Pin Assembly
* Firing Pin Assembly Includes Items #18, 23, 27 & 39
† Lever Guide Kit Includes Items # 14, 15, 16, 20 & 39
33
LEVER
37
GUIDE 13
20
KIT
9
26
36
33
EN
10
Housing
Release Lever
Retaining Ring
Rubber Grip
*