Elite RIZER Mode D'emploi page 33

the same promptness. In some cases, especially when there
are sudden power and/or speed variations, there might be
temporary gradient oscillations before the RIZER sets itself
on the correct gradient. This system means that the RIZER
can communicate with all home trainers sending workout
data via the ANT+FE-C protocol, even though they're not
specifically designed to work with the RIZER. Check the
"compatible home trainers" paragraph for more info on
RIZER compatibility.
- Wheelbase setting in the profile allows the RIZER to
simulate gradient more accurately. RIZER still works even
if the settings aren't there or they're inaccurate, though in
these cases the gradient adjusted by the RIZER might not be
accurate.
- RIZER can send steering angle measurements, though
not every cycling workouts software can manage such
information. Please contact the software producer to check
its compatibility with the angle data sent by the RIZER.
- App is connected via the Bluetooth Smart protocol.
- In order to set the proper tilt for the bicycle, RIZER uses the
"wheelbase" parameter to calculate the cursor movement.
An inaccurate value makes the gradient simulated by the
RIZER inaccurate even if it does not affect its operations.
09_MAINTENANCE
RIZER needs no specific maintenance.
Should you hear a creaking sound when the RIZER is
moving you can lubricate the central lifting spindle.
We suggest using a high viscosity moist or wet chain
lubricant to lubricate. Dry lubricants or low viscosity ones
quickly evaporate so they do not last as long.
This is the procedure:
- Tap and hold the three keys at the same time for 5
seconds. The keyboard LED light will start blinking and the
cursor will set itself at the minimum level.
- Once the fork support has been lowered, you can see the
screw that closes the lubrication hole. Remove the screw.
- Lubricate the central pin with short sprays or a spray
lubricant with straw.
- Tap one of the keys. RIZER will start moving up and down
multiple times, spreading the lubricant all along the pin.
Once this is done, the RIZER cursor will reposition at the
minimum value.
- Close the lubricant hole with the screw you previously
removed and make sure it does not stick out of the structure
as it might limit the fork support (Ref. X) movement range
during its operations.
- Tap one of the keys to complete the procedure. The
cursor will reposition on the zero value.
Note: do not use unblocking or degreasing agents.
10_PACKAGING
Proper packaging is essential should the RIZER need to be
sent to customer support or for other reasons.
- Remove the RIZER power supply cord;
- Place the RIZER in its original packaging;
On shipments, packages are often mistreated and undergo
strongs shocks, so if the device isn't properly packed or
it sits in a packaging different from the original one, it
might get irreparably damaged. This type of damage is not
covered by the warranty conditions.
Note: before shipping the RIZER or any of its components
to our customer support, please check with Elite, its
distributor or the retailer.
Any unplanned shipment might be rejected.
11_COPYRIGHT
No part of this manual may be reproduced or transmitted
without the written authorization of Elite S.r.l.
The Elite RIZER software and relative code are property
of Elite S.r.l.
12_PRODUCT MODIFICATIONS
Also in view of any technical update, ELITE reserves the
right to make changes to the products or their specifications
without being obliged to notify or inform the Customer
beforehand for:
a) changes that do not affect negatively the product
performance;
b) changes required to meet or improve the product
specifications;
c) changes necessary for the products to comply with the
applicable legal requirements.
ELITE also reserves the right to supply these products with
these improvements without being obliged to or responsible
for applying the same modifications to any previously
purchased products, reserving also the right to change
prices and model availability according to market conditions,
component availability and other corporate considerations.
13_DISCLAIMER
Elite S.r.l. is not liable for any temporary or permanent
damage to the physical integrity of the user, whether direct
or indirect, resulting from the use of the trainer.
14_INFORMATION ON PRODUCT DISPOSAL
1) WITHIN THE EUROPEAN UNION
This product conforms with European Directives
2002/95/CE, 2002/96/CE and 2003/108/CE.
The crossed bin symbol given on the equipment
or on the packaging indicates that at the end of its
service life the product must be collected
EN
33