Proper Use; Important Information - Scheppach HM80L Traduction Des Instructions D'origine

*S6, continuous operation periodic duty.
Identical duty cycles with a period at load followed
by a period at no load. Running time 10 minutes;
duty cycle is 25% of the running time.
The work piece must have a minimum height of
3mm and a minimum width of 10 mm.
Make sure that the workpiece is always secured
with the clamping device.
Information about noise development
The noise levels of this machine during operation are
as follows:
L
: 99.6dB(A) K=3dB(A)
pA
L
: 112.6dB(A) K=3dB(A)
wA
Wear hearing protection.
The effects of noise can cause a loss of hearing.
Total vibration values (vector sum - three directions)
determined in accordance with EN 61029.

Proper use

The mitre saw is used for the cutting of wood and
plastic, according to the machine size.
Warning! The supplied saw blade is only intended
for the sawing of wood! Do not use this blade for the
sawing of plastic!
The saw is not suitable for the cutting of firewood.
The machine may only be used in the intended man-
ner.
Only suitable saw blades may be used for the ma-
chine. The use of any type of cutting wheels is pro-
hibited.
An element of the intended use is also the obser-
vance of the safety instructions, as well as the as-
sembly instructions and operating information in the
operating manual.
Persons who operate and maintain the machine must
be familiar with the manual and must be informed
about potential dangers.
Any use beyond this is improper. The user/operator,
not the manufacturer, is responsible for damages or
injuries of any type resulting from this.
In addition, the applicable accident prevention regu-
lations must be strictly observed.
Other general occupational health and safety-related
rules and regulations must be observed.
The liability of the manufacturer and resulting dam-
ages are excluded in the event of modifications of
the machine.
Despite use as intended, specific risk factors cannot
be entirely eliminated. Due to the design and layout
of the machine, the following risks remain:
• Contact with the saw blade in the non-covered saw
area.
• Reaching into the running saw blade (cutting in-
jury).
• Kick-back of workpieces and workpiece parts.
• Saw blade breakage.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
• Ejection of faulty carbide parts of the saw blade.
• Hearing damage when the necessary hearing pro-
tection is not used.
• Harmful emissions of wood dusts during use in
enclosed areas.
Please observe that our equipment was not designed
with the intention of use for commercial or industrial
purposes. We assume no guarantee if the equipment
is used in commercial or industrial applications, or
for equivalent work.

Important information

Attention! The following basic safety measures must
be observed when using electric tools for protection
against electric shock, and the risk of injury and fire.
Read all these notices before using the electric tool
and keep the safety instructions for later reference.
Safe work
1 Keep the work area orderly
Disorder in the work area can lead to accidents.
–
Take environmental influences into account
2
Do not expose electric tools to rain.
–
– Do not use electric tools in a damp or wet en-
vironment.
Make sure that the work area is well-illuminated.
–
Do not use electric tools where there is a risk of
–
fire or explosion.
Protect yourself from electric shock
3
Avoid physical contact with earthed parts (e.g.
–
pipes, radiators, electric ranges, cooling units).
4 Keep other persons away
– Do not allow other persons, especially children,
to touch the electric tool or the cable. Keep them
away from your work area.
The operating person must be at least 18 years
–
of age; trainees must be at least 16 years, how-
ever only under supervision.
5 Securely store unused electric tools
Unused electric tools should be stored in a dry,
–
elevated or closed location out of the reach of
children.
Do not overload your electric tool
6
– They work better and more safely in the speci-
fied output range.
7 Use the correct electric tool
Do not use low-output electric tools for heavy
–
work.
Do not use the electric tool for purposes for
–
which it is not intended. For example, do not
use handheld circular saws for the cutting of
branches or logs.
Do not use the electric tool to cut firewood.
–
Wear suitable clothing
8
Do not wear wide clothing or jewellery, which
–
can become entangled in moving parts.
When working outdoors, anti-slip footwear is
–
recommended.
GB 21