Before Using The Unit; Setting Up The Massage Lounger - Panasonic REAL PRO Elite EP3513 Mode D'emploi

BEFORE USING THE UNIT

SETTING UP THE MASSAGE LOUNGER

After Removing Everything from the Box, You Should Have the Following
Massage Lounger
Armrests
Marks indicating left and right can be found
on the underside of each armrest.
Front Back
Connector Hose
Small holes on the inside
fabric are an intentional part
Air Plug
of the functional design.
Where to Use the Unit
Ensure there is adequate space for reclining.
Approx. 77" (195 cm)
Keep at least
4" (10 cm)
Approx. 14" Approx. 12"
Width approx. 27" (68 cm)
away from
(35 cm) (30 cm)
(approx. 33" (84 cm) with
wall, etc.
armrests attached)
Mat
Area where legrest Area where unit touches floor.
could touch floor.
Carrying in the Unit
Move the chair by having one person hold onto the rubber
section on the underside of the legrest and another person
use the handle on the back of the backrest.
Legrest Handle
Place your fingers in the groove.
Rubber
Section
8
All manuals and user guides at all-guides.com
Accessories
Pillow
Attachment Screws (M6#16) — 6
Left Armrest — 3
Right Armrest — 3
Control Panel Stand Attachment Screws
(M6#10) — 4
Plug Cover Attachment Screws
(M5#16) — 2
Control Panel Stand
Plug Covers — 2
Allen Key — 1
Clip
Control Panel
Stand Covers
Lock Switch Keys — 2
CAUTION
Keep at least
• Do not use the unit in areas with high humidity,
4" (10 cm)
such as the bathroom, etc. as this can lead to
away from
electric shock or other accidents.
wall, etc.
• Place the unit on a totally flat surface.
Failure to do so may result in the seat tipping over.
• Do not use the massage lounger in direct sunlight or in
places where it will be exposed to high temperatures,
such as in front of a heater, etc., as this can cause
discoloration or hardening of the synthetic leather.
• Place the unit on a mat to prevent floor damage.
• When placing a mat under the unit, the size of the mat
should be sufficient (at least 47#28 in. (120#70 cm)) to
cover the areas where the unit touches and the legrest
could touch the floor, as shown in the diagram on the left.
CAUTION
• Make certain the legrest has been retracted fully
to its original length.
Failure to observe this safeguard could result in injury
due to the legrest returning to its original length
when the unit is being moved.
• Use care to prevent pinching of hands or feet when letting
Mat
go of the legrest as its mechanism will cause it to slam shut.
• Use care to prevent lower back and other injuries that
could occur when lifting this heavy object (approx. 179
lbs (81 kg)).
ASSEMBLY
Attaching the Armrests (On Both Right and Left Sides)
1 1
(Cross-section)
0.2"
(4 mm)
Connecting the Air Plugs (On Both Right and Left Sides)
Allen Key
Attaching the Control Panel Stand to the Right or Left Armrest
Attachment Screw
(M6#10)
Allen Key
2
• Diagram shows attachment to right armrest.
Use the mark as
1. Insert the armrest into the unit.
a guide for insertion.
• Markings indicating left-hand and right-hand
sides can be found on the inside surface of
each armrest.
• Make sure the control panel cord does not
become pinched when fitting the right armrest
onto the unit.
Turn screws clockwise
2. Fasten the armrest with the
to tighten.
attachment screws.
• Set the three attachment screws in place first
2 2
and then tighten them firmly.
Use This Screw
#6
Allen Key Attachment Screw
(M6#16)
1. Insert the air plug.
• Push on the air plug until you hear it click into
place.
1
2. Place the plug cover over top of the
air plug and fasten with the screw.
2
Use This Screw
Air Plug
#2
Attachment Screw Plug Cover
(M5#16)
1. Decide which side to attach the
control panel stand to.
2. Fasten the control panel stand with
the attachment screws in four places.
• Set the four attachment screws in place first
and then tighten them firmly.
1
Use This Screw
#4
9