After Completing The Massage; Cleaning And Maintenance - Panasonic REAL PRO Elite EP3513 Mode D'emploi

AFTER COMPLETING THE MASSAGE

Return the Seat to the Original Position
1. Check that nothing is under the
legrest and that air is being released.
Check
that nothing
is under the
legrest.
3. Press twice to return the chair
to the upright position.
If no one is sitting in it,
the chair will stop part
way.
Disconnect the Power
Power Switch
2 1
34
All manuals and user guides at all-guides.com
2. Always return the legrest to its original
length if it has been slid out.
Legrest Slide
Lever
Pull back.
Raise legs slightly and
legrest returns.
4. If the pillow or back cushion has been
flipped back or the control panel has
been removed from its stand, return
them to their original positions.
off/on pre-programs
shiatsu deep swedish stretch quick
time remaining self program
user
intensity intensity intensity speed time
hands /arms lower body upper body
open
leg stretch vibration intensity neck / back
off/on off/on hands/ lower upper roller position
arms body body
1. Slide the power switch to the
"off" position.
2. Turn the lock switch key to the
"lock" position.
* Remove key and store out of reach of
children.
3. Unplug the power cord.

CLEANING AND MAINTENANCE

CAUTION
• Always unplug the unit before cleaning it. Never touch a power plug with wet hands.
Failure to follow these instructions may lead to electrocution or burns.
Areas Covered with Synthetic Leather
• Wipe these areas with a soft, dry cloth. (Do NOT
use cloths containing any kind of chemical, etc.)
• If the synthetic leather is particularly dirty, soak a soft
cloth in water or a 3~5% solution of mild detergent,
wring it out thoroughly and tap the surface with it.
Next, rinse the cloth in water, wring it out
thoroughly and then wipe any remaining detergent
from the surface, wipe the surfaces with a soft dry
cloth and allow them to dry naturally.
(Do NOT use a hair dryer to try to dry the surfaces
more quickly.)
ottoman reclining
self program
voice
• Do not allow these areas to come in contact with
open
self program time input
focus manual controls
plastic for extended periods of time as this may
lead to discoloration.
Moving the Unit
CAUTION
• Do not move the unit while someone is seated on it. Do not place objects on or sit, climb, or stand on
the legrest.
• When moving the unit using the wheels, remove all obstacles from around it, make sure the backrest is
in the upright position, lift it no higher than waist height (no higher than 31 in. (80 cm)) and roll it slowly.
Failure to do so may cause the unit to tip over, which may lead to damage or injury.
Lifting the Unit
• Move the chair by having one person hold onto the rubber
section on the underside of the legrest and another person
use the handle on the back of the backrest.
* Please hold the handle and legrest securely to avoid dropping
the unit as it may damage your floor.
Make sure the legrest is
retracted to the minimum length.
Hold onto the rubber section on
the underside of the legrest.
Do not hold onto the fabric.
Rubber Section
Mat
Pipe and Plastic Areas
(1) Wipe the unit with a cloth that has
been soaked in a mild detergent and
then thoroughly wrung out.
(2) Next wipe the unit with a cloth that
has been moistened with just water
and thoroughly wrung out.
* Make sure you thoroughly wring out
the cloth first when cleaning the
control panel.
(3) Allow the unit to dry naturally.
• Please do NOT use thinners, benzine
or alcohol.
Seat Fabric
Water
(1) Wipe the seat fabric with a cloth that
has been soaked in a mild detergent
and then thoroughly wrung out.
Mild Detergent
(2) Use a mild detergent and brush on
areas where the seat fabric has
become particularly soiled. Be careful
not to brush the fabric too much as
you may damage it.
(3) Next wipe the fabric with a cloth that
has been moistened with just water
and thoroughly wrung out.
(4) Allow the fabric to dry naturally.
Using the Wheels to Move the Unit
• Move the chair by holding onto the rubber section on the
underside of the legrest and using the wheels.
(It is easier to move the unit when the massage heads are
positioned at the top of the backrest.)
* Place a mat on the floor and gently roll the unit over it to avoid
damaging the floor.
Place the control
Make sure the legrest is
panel on the seat.
retracted to the minimum length.
Place the control
panel on the seat.
Roll the unit
slowly.
Handle
Place your fingers in the groove. Mat Wheels
Mild Detergent
Water
Water
Hold onto the rubber section
on the underside of the legrest.
Do not hold onto the fabric.
Rubber Section
35